Samsung HG40NC678DF User Manual Ver.1.0 (English) - Page 17

1. Connect the AUDIO OUT port of the TV to the PC/AUDIO port of the RJP. 2. Connect the AV IN VIDEO/L-AUDIO-R ports of the TV to the RCA port of the RJP. 3. Connect one of the HDMI IN ports of the TV to the HDMI port of the RJP. 4. Connect the EX-LINK port of the TV to the RS/232 port of the RJP. ✎✎ This Samsung TV is compatible with the Tele Adapt TA-7610 RJP only. yy RJP (Remote Jack Pack): The RJP is a hardware module that has different Audio Video inputs (A/V, Audio, PC and HDMI) and corresponding outputs. The corresponding outputs are connected from the RJP to the TV. The RJP communicates with the TV via RS232. The RJP communicates with the TV by sending messages regarding Active/Inactive sources. -- A group of hotel menu items let you assign numbered priorities to the jacks of the RJP. (See page 19). 1 is the highest priority and 3 is the lowest. When a guest connects external sources to the RJP jacks, the TV will automatically switch between sources based on the priority you have assigned them in the Menu. For example, lets say AV is set to 1 and HDMI to 2. If a guest has attached a device to the HDMI jack, and then plugs a device into the AV jack, the TV automatically switches to the device plugged into the AV jack (the jack with the higher priority). Note that a guest can also switch between devices manually by pushing a button on the RJP. ✎✎ When you set up the RJP, connect the RJP to HDMI 1, 2, or 3 or AV 1 or 2. yy To reset the RJP to its factory default state, press the AV and HDMI buttons simultaneously for 10 seconds. When all button LEDs blink 5 times, the RJP reset is complete. yy The RJP will automatically turn off any LEDs after 5 minutes to avoid unnecessary light pollution in the hotel room. The LEDs that were turned off will turn on again if the guest touches any of the buttons and the 5 minute timer will restart. If the guest then touches another source button, the TV will change to the selected source and the corresponding LED will be lit. yy After an RJP Reset or a TV Power OFF/ON, it takes approximately 10 seconds to establish communications between the TV and the RJP. yy The following table shows the approximate time in seconds it takes to switch from the TV to an input source, based on assigned or default priorities. ✎✎ Scenario 1 : When no inputs are connected. Source To Connect AV 2 Sec PC 0.7 Sec HDMI 3.9 Sec ✎✎ Scenario 2: When two or more inputs are connected to the RJP and one of the input sources is disconnected and then reconnected. Source Disconnect To Connect Total AV 4.5 Sec 2 Sec 6.5 Sec PC 0.7 Sec 0.7 Sec 1.4 Sec HDMI 3.9 Sec 3.9 Sec 7.8 Sec ✎✎ An example: If the RJP has all its live sources (AV, PC, and HDMI) connected, AV has been assigned the highest priority, the RJP is in HDMI mode, and a guest removes and reconnects the AV source, the minimum time required to switch to the AV source is 6.5 seconds. yy To play audio devices (Ipods, MP3 devices, etc.) through the RJP, you must turn Music Mode AV in the menu on. (See page 20) yy Music mode in the TA-7610 RJP is supported by the AV jack only. HDMI Music mode is available for the Guestlink RJP only. [HC670_677_678-ZA]Install Guide-X0ENG.indd 17 17 English 2014-03-17 10:02:26