Samsung ME19R7041F Installation Guide - Page 10

D. Aligning the wall plate, CAUTION, NOTE: DO NOT MOUNT THE PLATE AT THIS, TIME.

Get Samsung ME19R7041F PDF manuals and user guides View all Samsung ME19R7041F manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Step-by-step installation guide D. ALIGNING THE WALL PLATE HHolleeAA CeCnetneterrlliinne nontoctchheess Draw a vertical line oDnratwhea Vweartlilctaol Lminaerk tohneWcaelnl ftreomr oCfetnhter coaf TboinpeCtaabbinoevte. HHoorirzizoonntatallLLininee AArereaaEE CL HHoole BB HHoorriizzoonnttaallLLiinnee DDrraawwaahHoroizrioznotnatlallinlieneononthwe awllafllroamlong tbhoettboomttoomf "oRf ethaer "WRaeallrTWemallpTlaetme"p.late". CCfiAnAUgUeTrTIsOIOoNnN::sWWheaearpar rgegldolgoveevses.stotoavaoviodidcuctutitntigngfingers on sharp edges. 1. Draw a horizontal line on the wall at the bottom of the "Rear Wall Template". 2. Drill ⅝˝ holes for toggle bolts in 3 locations (Hole A, Hole B, Hole C) as shown in the illustration above. If the location of a hole lines up with a stud, drill a 3/16˝ hole for a wood screw. You cannot use a toggle bolt to attach the wall plate to a stud. 3. Holes A, B and C are inside area E. If none of these holes line up with a stud, find a stud in area E that lines up with a hole circle in Area E, and then drill a 3/16˝ hole into it for a wood screw. You must have at least one wood screw mounted firmly into a stud to support the weight of the microwave. Set the mounting plate aside. NOTE: DO NOT MOUNT THE PLATE AT THIS TIME. ME4000R_ME19R7041FS_AA_DE68-04585A-01_EN.indd 10 10 2021-03-25 오전 11:43:19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
10
Step-by-step installation guide
D. ALIGNING THE WALL PLATE
C
L
Horizontal Line
Draw a horizontal line on the wall along
the bottom of the “Rear Wall Template”.
Draw a vertical line
on the wall to mark
the center of the
cabinet above.
Horizontal Line
Horizontal Line
Area E
Centerline
notches
Hole A
Hole B
CAUTION
: Wear gloves to avoid cutting fingers on
sharp edges.
1
.
Draw a horizontal line on the wall at the bottom of
the “Rear Wall Template”.
2
.
Drill ⅝˝ holes for toggle bolts in 3 locations (Hole
A, Hole B, Hole C) as shown in the illustration
above. If the location of a hole lines up with
a stud, drill a
3
/
16
˝ hole for a wood screw. You
cannot use a toggle bolt to attach the wall plate
to a stud.
NOTE: DO NOT MOUNT THE PLATE AT THIS
TIME.
3
.
Holes A, B and C are inside area E. If none of
these holes line up with a stud, find a stud in area
E that lines up with a hole circle in Area E, and
then drill a
3
/
16
˝ hole into it for a wood screw. You
must have at least one wood screw mounted
firmly into a stud to support the weight of the
microwave.
Set the mounting plate aside.
ME4000R_ME19R7041FS_AA_DE68-04585A-01_EN.indd
10
ME4000R_ME19R7041FS_AA_DE68-04585A-01_EN.indd
10
2021-03-25
오전 11:43:19
2021-03-25
오전 11:43:19