Samsung ME19R7041F Installation Guide - Page 16

C. Use the top cabinet template to prepare the cabinet above, D. Mount the microwave oven

Get Samsung ME19R7041F PDF manuals and user guides View all Samsung ME19R7041F manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Step-by-step installation guide To use toggle bolts: MoMuonutnintingg PlaPtelate Spacing for Toggles More Than Wall Thickness TooggggleleWWinignsgs TTooggggllee BBooltt D. MOUNT THE MICROWAVE OVEN WWalll BBoolltt Enndd 3. Place the mounting plate against the wall, pinch the wings of each toggle together, and then insert the toggle wings of each toggle into and through the holes in the wall. NOTE: Before tightening the toggle bolts and wood screw, make sure the bottom of the Mounting plate runs along the bottom Horizontal line of the "Rear wall Template" and the Mounting plate is properly centered under the cabinet. CAUTION: Be careful to avoid pinching your fingers between the back of the mounting plate and the wall. 4. Tighten all bolts. Pull the plate away from the wall to help tighten the bolts. Tighten the screw. C. USE THE TOP CABINET TEMPLATE TO PREPARE THE CABINET ABOVE You need to drill holes for the top support screws and a hole large enough for the power cord to fit through. FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN. IMPORTANT: Do not grip the handle or use the handle during installation to support the microwave. NOTE: If your cabinet is metal, use the nylon grommet in the power cord hole to prevent the cord from being cut. NOTE: Filler blocks are required when mounting this unit under any cabinet with a recessed bottom or front overhang. (See page 9.) IMPORTANT: The case damage that will occur from over tightening screws if you do not use filler blocks is not covered under warranty. NOTE: When mounting the microwave oven, thread the power cord through hole in the bottom of the top cabinet. Keep it tight throughout Steps 1-3. Do not pinch the cord or lift the oven by pulling cord. 1. Lift the microwave, tilt it forward, and hook the slots at the back bottom edge onto the four lower tabs of the mounting plate. • Read the instructions on the TOP CABINET TEMPLATE. • Tape it underneath the top cabinet. • Drill the holes, following the instructions on the TOP CABINET TEMPLATE. CAUTION: Wear safety goggles when drilling holes in the cabinet bottom. 2. Rotate the front of the oven up against the cabinet bottom. ME4000R_ME19R7041FS_AA_DE68-04585A-01_EN.indd 16 16 2021-03-25 오전 11:43:21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
16
Step-by-step installation guide
To use toggle bolts:
Bolt End
Mounting
Plate
Toggle
Bolt
Wall
Toggle Wings
3
.
Place the mounting plate against the wall, pinch the
wings of each toggle together, and then insert the
toggle wings of each toggle into and through the
holes in the wall.
NOTE
: Before tightening the toggle bolts and wood
screw, make sure the bottom of the Mounting plate
runs along the bottom Horizontal line of the “Rear wall
Template” and the Mounting plate is properly centered
under the cabinet.
CAUTION
: Be careful to avoid pinching your fingers
between the back of the mounting plate and the wall.
4
.
Tighten all bolts. Pull the plate away from the wall to
help tighten the bolts. Tighten the screw.
C. USE THE TOP CABINET TEMPLATE
TO PREPARE THE CABINET ABOVE
You need to drill holes for the top support screws and a
hole large enough for the power cord to fit through.
•
Read the instructions on the TOP CABINET
TEMPLATE.
•
Tape it underneath the top cabinet.
•
Drill the holes, following the instructions on the TOP
CABINET TEMPLATE.
CAUTION
: Wear safety goggles when drilling holes in
the cabinet bottom.
D. MOUNT THE MICROWAVE OVEN
FOR EASIER INSTALLATION AND PERSONAL SAFETY,
WE RECOMMEND THAT TWO PEOPLE INSTALL THIS
MICROWAVE OVEN.
IMPORTANT: Do not grip the handle or use
the handle during installation to support the
microwave.
NOTE
: If your cabinet is metal, use the nylon grommet in
the power cord hole to prevent the cord from being cut.
NOTE
: Filler blocks are required when mounting this
unit under any cabinet with a recessed bottom or front
overhang. (See page 9.)
IMPORTANT: The case damage that will occur
from over tightening screws if you do not use filler
blocks is not covered under warranty.
NOTE
: When mounting the microwave oven, thread
the power cord through hole in the bottom of the top
cabinet. Keep it tight throughout Steps 1–3. Do not
pinch the cord or lift the oven by pulling cord.
1
. Lift the microwave, tilt it
forward, and hook the slots
at the back bottom edge
onto the four lower tabs of
the mounting plate.
2
. Rotate the front
of the oven
up against the
cabinet bottom.
ME4000R_ME19R7041FS_AA_DE68-04585A-01_EN.indd
16
ME4000R_ME19R7041FS_AA_DE68-04585A-01_EN.indd
16
2021-03-25
오전 11:43:21
2021-03-25
오전 11:43:21