Samsung RS257BABB Service Guide - Page 19

Remove the Xtra Space

Get Samsung RS257BABB PDF manuals and user guides View all Samsung RS257BABB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Mechanical Disassembly top of the liner, and slide the ice maker in. 5. Tighten the screws (2) of the ice maker support. FRONT LOCKING TAB FRONT OF ICE TRAY TAB HOLES GEARED MOTOR SHAFT Auger Motor Case The ice maker is located inside of the ice dispenser assembly. 1. Remove ice maker support screws (2), and slide out. 2. Disconnect the ice maker wire connector. 3. Unlock the locking tabs to separate the ice maker kit. SUPPORT OF ICE-MAKER LOCKING TAB WIRE CONNECTOR This shelf is designed to support the ice maker ＆ ice dispensed and Xtra SpaceTM. 1. Remove the Xtra SpaceTM cover to push it down and pull front. 2. Slide the partition out. 3. Remove the screws (2) on the bottom front of the case. 4. Slide out the case while disconnecting the wire connect. Partition ICE-MAKER KIT In order to assemble the icemaker kit. 1. Assemble the geared motor shaft and the front of ice tray. 2. Lift the front locking tab and assemble the ice maker kit. 3. Connect the ice maker wire connector. 4. Match the tab holes and tabs(2) located on the 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
19
Mechanical Disassembly
The ice maker is located inside of the ice dispenser
assembly.
1.
Remove ice maker support screws (2), and slide out.
2. Disconnect the ice maker wire connector.
3.
Unlock the locking tabs to separate the ice maker kit.
In order to assemble the icemaker kit.
1. Assemble the geared motor shaft and the front of
ice tray.
2. Lift the front locking tab and assemble the ice
maker kit.
3. Connect the ice maker wire connector.
4. Match the tab holes and tabs(2) located on the
top of the liner, and slide the ice maker in.
5. Tighten the screws (2) of the ice maker support.
This shelf is designed to support the ice maker
＆
ice dispensed and Xtra Space
TM
.
1. Remove the Xtra Space
TM
cover to push it down
and pull front.
2. Slide the partition out.
3. Remove the screws (2) on the bottom front of the
case.
4. Slide out the case while disconnecting the wire
connect.
Auger
Motor Case
Partition
WIRE CONNECTOR
SUPPORT OF ICE-MAKER
ICE-MAKER KIT
LOCKING TAB
FRONT OF ICE TRAY
FRONT LOCKING TAB
TAB HOLES
GEARED MOTOR SHAFT