Samsung SMH1816B Installation Instructions - Page 16

Use The Top Cabinet, Template To Prepare, The Top Cabinet, Mount The Microwave - no power

Get Samsung SMH1816B PDF manuals and user guides View all Samsung SMH1816B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Step-by-step installation guide To use toggle bolts: MoMuonutnintingg PlaPtlaete SSppaacciinnggfoforrTTooggglgelseMs oMreore TThhaann WWaallll TThhicickknneessss TToogggllee WWininggss TToogggglele BBooltlt D. Mount the microwave 3. oven WWaalll BBoolltt End FOR EASIER INSTALLATION AND PERSONAL 3. Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate. NOTE: Before tightening the toggle bolts and wood SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN. IMPORTANT: Do not grip or use handle during installation. screw, make sure the bottom of the Mounting plate NOTE: If your cabinet is metal, use the nylon runs along the bottom Horizontal line of the "Rear wall grommet in the power cord hole to prevent the cord Template" and the Mounting plate is properly centered from being cut. under the cabinet. NOTE: Filler blocks are required when mounting this CAUTION: Be careful to avoid pinching your fingers between the back of the mounting plate and the wall. unit under any cabinet with a recessed bottom or front overhang. (See page 9.) 4. 5. 4. Tighten all bolts. Pull the plate away from the wall IMPORTANT: The case damage that will occur to help tighten the bolts. Tighten the screw. from over tightening screws if you do not use filler blocks is not covered under warranty. C. Use the top cabinet NOTE: When mounting the microwave oven, thread template to prepare the top cabinet the power cord through hole in the bottom of top cabinet. Keep it tight throughout Steps 1-3. Do not pinch the cord or lift the oven by pulling cord. You need to drill holes for the top support screws and a hole large enough for the power cord to fit through. 1. Lift the microwave, tilt it forward, and hook the slots at the back bottom edge onto the four lower tabs of the mounting plate. 6. • Read the instructions on the TOP CABINET TEMPLATE. • Tape it underneath the top cabinet. • Drill the holes, following the instructions on the TOP CABINET TEMPLATE. CAUTION: Wear safety goggles when drilling holes in the cabinet bottom. 2. Rotate the front of the oven up against the cabinet bottom. 16 SMH1816_XAA-DE68-03943A-02-EN_120725.indd 16 2012-07-25 �� 7:49:19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
16
Step-by-step installation guide
To use toggle bolts:
Spacing for Toggles More
Than Wall Thickness
Bolt End
Mounting
Plate
Toggle
Bolt
Wall
Toggle Wings
3
.
Place the mounting plate against the wall and
insert the toggle wings into the holes in the wall to
mount the plate.
NOTE
: Before tightening the toggle bolts and wood
screw, make sure the bottom of the Mounting plate
runs along the bottom Horizontal line of the “Rear wall
Template” and the Mounting plate is properly centered
under the cabinet.
CAUTION
: Be careful to avoid pinching your fingers
between the back of the mounting plate and the wall.
4
.
Tighten all bolts. Pull the plate away from the wall
to help tighten the bolts. Tighten the screw.
C.
USE THE TOP CABINET
TEMPLATE TO PREPARE
THE TOP CABINET
You need to drill holes for the top support screws and
a hole large enough for the power cord to fit through.
•
Read the instructions on the TOP CABINET
TEMPLATE.
•
Tape it underneath the top cabinet.
•
Drill the holes, following the instructions on the
TOP CABINET TEMPLATE.
CAUTION
: Wear safety goggles when drilling holes in
the cabinet bottom.
D.
MOUNT THE MICROWAVE
OVEN
FOR EASIER INSTALLATION AND PERSONAL
SAFETY, WE RECOMMEND THAT TWO PEOPLE
INSTALL THIS MICROWAVE OVEN.
IMPORTANT: Do not grip or use handle during
installation.
NOTE
: If your cabinet is metal, use the nylon
grommet in the power cord hole to prevent the cord
from being cut.
NOTE
: Filler blocks are required when mounting this
unit under any cabinet with a recessed bottom or
front overhang. (See page 9.)
IMPORTANT: The case damage that will occur
from over tightening screws if you do not use
filler blocks is not covered under warranty.
NOTE
: When mounting the microwave oven, thread
the power cord through hole in the bottom of top
cabinet. Keep it tight throughout Steps 1–3. Do not
pinch the cord or lift the oven by pulling cord.
1
.
Lift the microwave, tilt
it forward, and hook
the slots at the back
bottom edge onto the
four lower tabs of the
mounting plate.
2
.
Rotate the front of
the oven up against
the cabinet bottom.
3
.
4
.
5
.
6
.
SMH1816_XAA-DE68-03943A-02-EN_120725.indd
16
2012-07-25
�� 7:49:19