Samsung WF56H9100AG/A2 User Manual Ver.0 (English, French, Spanish) - Page 16

Installing your Washer

Get Samsung WF56H9100AG/A2 PDF manuals and user guides View all Samsung WF56H9100AG/A2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

installing your washer STEP 3 Installing your Washer 1. If you use a standpipe, make sure the connection between the drain hose and the standpipe is NOT airtight. The standpipe must be at least 18 in or 46 cm high. You must always exercise caution to avoid collapsing or damaging the drain hose. For best results, the drain hose should not be restricted in any way - by elbows, couplings, or excessive length. For situations where the drain hose cannot 96" Max 18" Min be conveniently elevated to at least 18 in or 46 cm, the drain hose must be supported. If the drain hose is installed below 18"(46cm), water can be drained due to the cause of a siphon phenomenon. This will cause the washer to display a "4E" error. Laundry tub Standpipe Hose retainer Tie strap 96" Max 18" Min The drain hose can be installed to a 96" (245cm) maximum, however, the drain capabilities can be reduced at this height. This can cause the washer to have an odor because of remaining water in the drain system. 1RPRUHWKDQ ರ FP +RVH*XLGH Connect the hose guide within 6"(15cm) from the end of the drain hose. If the drain hose is extended more than 6"(15cm) Cold Hot beyond the end of the hose guide, mold or microorganisms could spread to the inside of the washer. 2. Check the inlet hose to ensure a rubber washer is inside each fill hose. Rubber Washer Thread the inlet hoses onto the HOT and COLD faucet connections. On the other end of the hose, check for one rubber washer per hose and attach each fill hose to the correct water valve on the washer. Make sure the hose with Hot printed on it is attached to the HOT faucet and HOT water valve. Tighten by hand until snug, then two- thirds of a turn with a pliers or wrench. For correct water use, connect both HOT and COLD water valves. If either or both are not connected, a "4E" error can occur. COLD HOT 3. Turn on the "HOT" and "COLD" water supply and check the water valve and the water supply connections for leaks. 64&3 8 JOEE 16_ English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
16_
English
installing your washer
STEP 3
Installing your Washer
1.
If you use a standpipe, make sure the connection
between the drain hose and the standpipe is NOT
airtight. The standpipe must be at least 18 in or 46
cm high.
You must always exercise caution to avoid
collapsing or damaging the drain hose. For best
results, the drain hose should not be restricted
in any way – by elbows, couplings, or excessive
length. For situations where the drain hose cannot
be conveniently elevated to at least 18 in or 46 cm,
the drain hose must be supported.
If the drain hose is installed below 18"(46cm),
water can be drained due to the cause of a siphon
phenomenon. This will cause the washer to display a
“4E” error.
The drain hose can be installed to a 96" (245cm)
maximum, however, the drain capabilities can be
reduced at this height.  This can cause the washer to
have an odor because of remaining water in the drain
system.
Connect the hose guide within 6"(15cm) from the end
of the drain hose. If the drain hose is extended more than 6"(15cm)
beyond the end of the hose guide, mold or microorganisms could
spread to the inside of the washer.
2.
Check the inlet hose to ensure a rubber washer is inside each fill hose.
Thread the inlet hoses onto the HOT and COLD faucet connections.
On the other end of the hose, check for one rubber washer per hose
and attach each fill hose to the correct water valve on the washer.
Make sure the hose with Hot printed on it is attached to the HOT
faucet and HOT water valve. Tighten by hand until snug, then two-
thirds of a turn with a pliers or wrench.
For correct water use, connect both HOT and COLD water valves. If either or both are not
connected, a “4E”
error can occur.
3.
Turn on the “HOT” and “COLD” water supply and check the water
valve and the water supply connections for leaks.
COLD
HOT
96” Max
18” Min
96” Max
18” Min
Hose
retainer
Tie strap
Laundry tub
Standpipe
Cold
Hot
Rubber
Washer
(USER)WF56H9100-03404A_EN.indd
16
2014-3-7
10:58:19