Sanyo FW55C46F-B Owners Manual - Page 20

Use your TV, Switching on your TV and putting it in standby mode, Adjusting volume, Switching channels

Get Sanyo FW55C46F-B PDF manuals and user guides View all Sanyo FW55C46F-B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

3 Use your TV Switching on your TV and putting it in standby mode TV Remote control Switching channels TV Remote control 20 .English To turn the TV on from standby or off to standby ● Press B on the TV or the remote control. Note(s) ● Energy consumption contributes to air and water pollution. When the AC power cord is plugged in, your TV consumes energy with a very low standby power consumption. Adjusting volume TV Remote control To select channels by using CH H / I or CH + / - ● Press CH H (up) / I （down) on the TV or press CH + / - on the remote control. To select channels by using the NUMBER buttons Digital TV operation ● For digital channels, press a number followed by a dot "•" and the corresponding sub channel number. - When selecting digital channel 11.1 Be sure to press • before entering the subchannel number. To decrease or increase volume ● Press VOL J / K on the TV or press VOL + / - on the remote control. VOL J (-) : Volume down VOL K (+) : Volume up To mute or unmute sound ● Press D on the remote control to mute the sound. ● Press D again or VOL + / - to recover the original sound. Cable / NTSC (Analog) TV operation - When selecting cable or analog channel 11 Press PREV.CH to return to the previously viewed channel. Note(s) ● To select the non-memorized channels, use the NUMBER buttons. ● Channel not available or No signal will appear on the TV screen after the subchannel broadcast is over. ● Audio only message will appear on the TV screen, when you receive only sound signal. Continued on next page.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
3
Use your TV
Switching on your TV and putting it in
standby mode
Remote control
TV
To turn the TV on from standby or off to standby
●
Press
B
on the TV or the remote control.
Note(s)
●
Energy consumption contributes to air and water pollution. When the AC power cord is
plugged in, your TV consumes energy with a very low standby power consumption.
Adjusting volume
Remote control
TV
To decrease or increase volume
●
Press
VOL
J
/
K
on the TV or press
VOL + / –
on the remote control.
VOL
J
(–) : Volume down
VOL
K
(+) : Volume up
To mute or unmute sound
●
Press
D
on the remote control to mute the sound.
●
Press
D
again or
VOL + / –
to recover the original sound.
Switching channels
TV
Remote control
To select channels by using CH
H
/
I
or CH + / –
●
Press
CH
H
(up) /
I
（
down) on the TV or press
CH + / –
on the remote
control.
To select channels by using the NUMBER buttons
Digital TV operation
●
For digital channels, press a number followed by a dot “
•
” and the
corresponding sub channel number.
–
When selecting digital channel 11.1
Be sure to press
•
before entering the subchannel number.
Cable / NTSC (Analog) TV operation
–
When selecting cable or analog channel 11
Press
PREV.CH
to return to the previously viewed channel.
Note(s)
●
To select the non-memorized channels, use
the NUMBER buttons
.
●
Channel not available
or
No signal
will appear on the TV screen after the subchannel
broadcast is over.
●
Audio only
message will appear on the TV screen, when you receive only sound signal.
20
.
English
Continued on next page.