Sanyo FW55C46F-B Owners Manual - Page 45

USB upgrade, Network updates, Setup, Update software, Network

Get Sanyo FW55C46F-B PDF manuals and user guides View all Sanyo FW55C46F-B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

USB upgrade You can upgrade the software by using USB memory stick. 1 Connect your USB memory stick with the upgrade file to the USB terminal on the side of your TV. 2 Press Z and use J K to select Setup then press OK. 3 Use H I J K to select Update software, then press OK. 4 Use H I to select USB, then press OK. 5 Use H I J K to select the desired update file, then press OK. 6 Use J K to select Yes, then press OK. ● Read the on-screen instructions and confirm that you want to continue with the installation. Software update is in progress. Please wait. Do not remove the USB storage device or turn the TV off while upgrade is in progress. 7 When the software upgrade is completed, press B to set the unit into standby mode, then remove the USB memory stick. 8 Unplug the AC power cord for a few seconds from AC outlet and plug it again. 9 Press B again to turn the unit on. ● The TV starts up with the new software. ● For further assistance, please contact call center. 45 .English Network updates You can update the software by connecting the unit to the internet. 1 Press Z and use J K to select Setup then press OK. 2 Use H I J K to select Update software, then press OK. 3 Use H I to select Network, then press OK. 4 Use J K to select Yes, then press OK. ● This unit will then start checking for the latest FirmWare (software) 5 version. Confirmation message will appear. Use J K to select Yes, then press OK. ● The unit will start downloading the latest FirmWare (software) version. ● The unit will start updating the FirmWare (software) version. 6 ● It may take a while to complete the updating. When the software update is complete, press B to make sure the unit goes to standby mode. 7 Unplug the AC power cord for a few seconds from AC outlet and plug it again. 8 Press B again to turn the unit on. ● The TV starts up with the new software. For further assistance, please contact call center. Note(s) ● In order to update software via the Internet, you must connect the unit to the Internet and set up necessary settings. Connect to network L p. 39 Network settings L p. 40 ● Please do not unplug the AC power cord or Ethernet cable while executing the Network updates. ● All settings will remain the same even if you update the software version. ● The version of net service will also be updated if newer version of net service is available when updating the firmware. ● When you start up the TV or a net service after executing the software update, a message may appear on the screen prompting for software update again. In this case, please select Update to start USB update or network update. For further assistance, please contact call center. Continued on next page.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
USB upgrade
You can upgrade the software by using USB memory stick.
1
Connect your USB memory stick with the upgrade file to the USB
terminal on the side of your TV.
2
Press
Z
and use
J
K
to select
Setup
then press
OK
.
3
Use
H
I
J
K
to select
Update software
, then press
OK
.
4
Use
H
I
to select
USB
, then press
OK
.
5
Use
H
I
J
K
to select the desired update file, then press
OK
.
6
Use
J
K
to select
Yes
, then press
OK
.
●
Read the on-screen instructions and confirm that you want to
continue with the installation.
Do not remove the USB storage device or turn the TV off
while upgrade is in progress.
Software update is in progress. Please wait.
7
When the software upgrade is completed, press
B
to set the unit
into standby mode, then remove the USB memory stick.
8
Unplug the AC power cord for a few seconds from AC outlet and
plug it again.
9
Press
B
again to turn the unit on.
●
The TV starts up with the new software.
●
For further assistance, please contact call center.
Network updates
You can update the software by connecting the unit to the internet.
1
Press
Z
and use
J
K
to select
Setup
then press
OK
.
2
Use
H
I
J
K
to select
Update software
, then press
OK
.
3
Use
H
I
to select
Network
, then press
OK
.
4
Use
J
K
to select
Yes
, then press
OK
.
●
This unit will then start checking for the latest FirmWare (software)
version.
5
Confirmation message will appear.
Use
J
K
to select
Yes
, then press
OK
.
●
The unit will start downloading the latest FirmWare (software)
version.
●
The unit will start updating the FirmWare (software) version.
●
It may take a while to complete the updating.
6
When the software update is complete, press
B
to make sure the
unit goes to standby mode.
7
Unplug the AC power cord for a few seconds from AC outlet and
plug it again.
8
Press
B
again to turn the unit on.
●
The TV starts up with the new software.
For further assistance, please contact call center.
Note(s)
●
In order to update software via the Internet, you must connect the unit to the Internet and
set up necessary settings.
Connect to network
L
p. 39
Network settings
L
p. 40
●
Please do not unplug the AC power cord or Ethernet cable while executing the
Network
updates
.
●
All settings will remain the same even if you update the software version.
●
The version of net service will also be updated if newer version of net service is available
when updating the firmware.
●
When you start up the TV or a net service after executing the software update, a message
may appear on the screen prompting for software update again. In this case, please select
Update
to start USB update or network update. For further assistance, please contact call
center.
45
.
English
Continued on next page.