Schwinn 450 Elliptical Assembly and Owner's Manual - Page 27

Remote Heart Rate Monitor, Contact Heart Rate Sensors - parts

Get Schwinn 450 Elliptical PDF manuals and user guides View all Schwinn 450 Elliptical manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Pulse (Heart Rate) The Pulse display shows the heart rate in beats per minute (BPM) from the heart rate monitor. Consult a physician before you start an exercise program. Stop exercising if you feel pain or tightness in your chest, become short of breath, or feel faint. Contact your doctor before you use the machine again. Use the values calculated or measured by the machine's computer for reference purposes only. Remote Heart Rate Monitor Monitoring your Heart Rate is one of the best procedures to control the intensity of your exercise. Contact Heart Rate (CHR) sensors are installed to send your heart rate signals to the Console. The Console can also read telemetry HR signals from a Heart Rate Chest Strap Transmitter that operates in the 4.5kHz - 5.5kHz range. Note: The heart rate chest strap must be an uncoded heart rate strap from Polar Electro or an uncoded POLAR® compatible model. (Coded POLAR® heart rate straps such as POLAR® OwnCode® chest straps will not work with this equipment.) If you have a pacemaker or other implanted electronic device, consult your doctor before using a wireless chest strap or other telemetric heart rate monitor. Contact Heart Rate Sensors Contact Heart Rate (CHR) sensors send your heart rate signals to the Console. The CHR sensors are the stainless steel parts of the Handlebars. To use, put your hands comfortably around the sensors. Be sure that your hands touch both the top and the bottom of the sensors. Hold firm, but not too tight or loose. Both hands must make contact with the sensors for the Console to detect a pulse. After the Console detects four stable pulse signals, your initial pulse rate will be shown. Once the Console has your initial heart rate, do not move or shift your hands for 10 to 15 seconds. The Console will now validate the heart rate. Many factors influence the ability of the sensors to detect your heart rate signal: • Movement of the upper body muscles (including arms) produces an electrical signal (muscle artifact) that can interfere with pulse detection. Slight hand movement while in contact with the sensors can also produce interference. • Calluses and hand lotion may act as an insulating layer to reduce the signal strength. • Some Electrocardiogram (EKG) signals generated by individuals are not strong enough to be detected by the sensors. 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
27
Pulse (Heart Rate)
The Pulse display shows the heart rate in beats per minute (BPM) from the heart rate monitor.
Consult a physician before you start an exercise program. Stop exercising if you feel pain or
tightness in your chest, become short of breath, or feel faint. Contact your doctor before you
use the machine again. Use the values calculated or measured by the machine’s computer
for reference purposes only.
Remote Heart Rate Monitor
Monitoring your Heart Rate is one of the best procedures to control the intensity of your exercise.
Contact Heart Rate (CHR) sensors are installed to send your heart rate signals to the Console. The
Console can also read telemetry HR signals from a Heart Rate Chest Strap Transmitter that oper-
ates in the 4.5kHz - 5.5kHz range.
Note:
The heart rate chest strap must be an uncoded heart rate strap from Polar Electro or an
uncoded POLAR
®
compatible model. (Coded POLAR
®
heart rate straps such as POLAR
®
OwnCode
®
chest straps will not work with this equipment.)
If you have a pacemaker or other implanted electronic device, consult your doctor before
using a wireless chest strap or other telemetric heart rate monitor.
Contact Heart Rate Sensors
Contact Heart Rate (CHR) sensors send your heart rate signals to the Console. The CHR sensors
are the stainless steel parts of the Handlebars. To use, put your hands comfortably around the
sensors. Be sure that your hands touch both the top and the bottom of the sensors. Hold firm, but
not too tight or loose. Both hands must make contact with the sensors for the Console to detect a
pulse. After the Console detects four stable pulse signals, your initial pulse rate will be shown.
Once the Console has your initial heart rate, do not move or shift your hands for 10 to 15 seconds.
The Console will now validate the heart rate. Many factors influence the ability of the sensors to
detect your heart rate signal:
•
Movement of the upper body muscles (including arms) produces an electrical signal (muscle
artifact) that can interfere with pulse detection. Slight hand movement while in contact with the
sensors can also produce interference.
•
Calluses and hand lotion may act as an insulating layer to reduce the signal strength.
• Some Electrocardiogram (EKG) signals generated by individuals are not strong enough to be
detected by the sensors.