Sharp 37D7U LC-26D7U LC-32D7U LC-37D7U Operation Manual - Page 60

Using external equipment, Setting the Recording Mode i.LINK, Setting the Standby Mode i.LINK

Get Sharp 37D7U - LC - 37inch LCD TV PDF manuals and user guides
UPC - 074000362727
View all Sharp 37D7U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

Using external equipment Setting the Recording Mode (i.LINK) Setting the Standby Mode (i.LINK) • The function for automatically adjusting the recording mode of connected i.LINK devices can be turned on or off. • Since most of the currently available i.LINK devices automatically recognize the transfer rates of the pictures and sound being recorded and control the recording mode accordingly, you should always set this Mode to "Pass through" in normal circumstances. • Depending on the i.LINK devices used and the type of broadcast being recorded, this TV may not adjust the recording mode properly. In this case, please set the "Recording Mode" to "Pass through". 1 Press MENU and the MENU screen displays. • Power consumption during standby mode can be minimized by changing the setting of the "Standby Mode" in "i.LINK Setup". • When i.LINK is not in use, select "Inactive" in "Standby Mode". 1 Press MENU and the MENU screen displays. 2 Press c/d to select "Digital Setup". 3 Press a/b to select "i.LINK Setup", and then press ENTER. 2 Press c/d to select "Digital Setup". 4 Press a/b to select "Standby Mode", and then press ENTER. 3 Press a/b to select "i.LINK Setup", and then press ENTER. 5 Press c/d to select "Active" or "Inactive", and then press ENTER. 4 Press a/b to select "Recording Mode", and then press ENTER. "Active": Power continues to pass through the i.LINK circuit so data can be relayed. "Inactive": Power consumption is minimized during stand-by mode. Data cannot be relayed at this 5 Press c/d to select "Auto" or "Pass setting. through", and then press ENTER. NOTE • Normally, this should be set to "Pass through". • When the main power of the TV is in standby mode (POWER indicator lights off), i.LINK control commands cannot be received from an i.LINK device. This does not change even if the "Standby Mode" is set to "Active". To control the TV from an i.LINK device, turn the TV power on (POWER indicator lights up in blue). • Data cannot be relayed between i.LINK devices when all the following conditions are met: 1) More than one i.LINK device is connected to the TV with i.LINK cables, 2) "Standby Mode" is set to "Inactive", and 3) The power of the TV is in standby mode (POWER indicator lights off). When the TV is connected between two i.LINK devices in series, select "Active" in "Standby Mode" or connect the TV at an end of the series as shown in the diagram. 59

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
59
Using external equipment
Setting the Recording Mode (i.LINK)
•
The function for automatically adjusting the recording
mode of connected i.LINK devices can be turned
on or off.
• Since most of the currently available i.LINK devices
automatically recognize the transfer rates of the
pictures and sound being recorded and control the
recording mode accordingly,
you should always
set this Mode to “Pass through” in normal
circumstances
.
•
Depending on the i.LINK devices used and the type
of broadcast being recorded, this TV may not adjust
the recording mode properly. In this case, please
set the “Recording Mode” to “Pass through”.
Press
MENU
and the MENU screen displays.
Press
c
/
d
to select “Digital Setup”.
Press
a
/
b
to select “i.LINK Setup”, and then
press
ENTER
.
1
2
3
Press
a
/
b
to select “Recording Mode”, and
then press
ENTER
.
4
Press
c
/
d
to select “Auto” or “Pass
through”, and then press
ENTER
.
•
Normally, this should be set to “Pass through”.
5
Setting the Standby Mode (i.LINK)
• Power consumption during standby mode can be
minimized by changing the setting of the “Standby
Mode” in “i.LINK Setup”.
• When i.LINK is not in use, select “Inactive” in
“Standby Mode”.
Press
MENU
and the MENU screen displays.
Press
c
/
d
to select “Digital Setup”.
Press
a
/
b
to select “i.LINK Setup”, and then
press
ENTER
.
1
2
3
Press
a
/
b
to select “Standby Mode”, and
then press
ENTER
.
4
Press
c
/
d
to select “Active” or “Inactive”,
and then press
ENTER
.
5
“Active”: Power continues to pass through the i.LINK
circuit so data can be relayed.
“Inactive”: Power consumption is minimized during
stand-by mode. Data cannot be relayed at this
setting.
NOTE
• When the main power of the TV is in standby mode
(POWER indicator lights off), i.LINK control commands
cannot be received from an i.LINK device. This does not
change even if the “Standby Mode” is set to “Active”. To
control the TV from an i.LINK device, turn the TV power
on (POWER indicator lights up in blue).
•
Data cannot be relayed between i.LINK devices when all
the following conditions are met: 1) More than one i.LINK
device is connected to the TV with i.LINK cables, 2)
“Standby Mode” is set to “Inactive”, and 3) The power of
the TV is in standby mode (POWER indicator lights off).
When the TV is connected between two i.LINK devices in
series, select “Active” in “Standby Mode” or connect the
TV at an end of the series as shown in the diagram.