Sharp PN-K321 Operation Manual - Page 10

Installing the stand (supplied

Get Sharp PN-K321 PDF manuals and user guides View all Sharp PN-K321 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Installing the stand (supplied) Caution • Disconnect all cables from the monitor. • Firmly tighten the installation screws (supplied) with the hex wrench (supplied). • Ensure that you have sufficient space to work. nAttaching the stand Remove all packaging materials before starting work. To prevent the table (etc.) from being damaged by the stand pedestal, spread a thick, soft cloth (blanket, etc.) and work on the cloth. 1. Insert the stand strut into the packaging material (upper left) as shown. Packing material (upper left) 5. Fasten the stand to the monitor with the supplied screws (M4 x 10 with washers) (x4). Use the supplied hex wrench. • Landscape Screw (M4 x 10 with washers) Front 2. While supporting the stand pedestal with your hand, fasten to the stand strut with the supplied countersunk screws (M4 x 6 without washers) (x5). Use the supplied hex wrench. Countersunk screw (M4 x 6 without washers) • Portrait Operation buttons Screw (M4 x 10 with washers) Front 1 Pedestal * A bag containing the screws (supplied) and hex wrench (supplied) is attached to the round hole in the stand pedestal. Insert by hooking the tab 2 Fixing pin 3. Spread a thick, soft cloth (blanket, etc.) that will prevent damage to the LCD panel on a stable flat surface where the entire monitor can be placed, and place the monitor with the LCD panel face down on the cloth. 4. Place the stand on the monitor. Hook the tab on the stand under the mounting plate (preinstalled on monitor). * If the monitor will be used in the portrait orientation, pull out the fixing pin (1), and insert it into the hole (2) as shown above. * To remove the stand, place the monitor and stand as shown above and remove the screws. Caution • Adhere to the following when installing the monitor in its portrait orientation. Failing to adhere to the following may cause malfunctions. - Install the monitor such that the operation buttons are located on the top side. - Set the MONITOR on the MONITOR menu to PORTRAIT. (See page 20.) Tab E 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
10
E
Installing the stand (supplied)
Caution
•
Disconnect all cables from the monitor.
•
Firmly tighten the installation screws (supplied) with the hex
wrench (supplied).
•
Ensure that you have sufficient space to work.
n
Attaching the stand
Remove all packaging materials before starting work.
To prevent the table (etc.) from being damaged by the stand
pedestal, spread a thick, soft cloth (blanket, etc.) and work on
the cloth.
1. Insert the stand strut into the packaging material (upper
left) as shown.
Front
Packing material
(upper left)
2.
While supporting the stand pedestal with your hand,
fasten to the stand strut with the supplied countersunk
screws (M4 x 6 without washers) (x5).
Use the supplied hex wrench.
Countersunk screw
(M4 x 6 without washers)
Insert by hooking the tab
Pedestal
* A bag containing the screws
(supplied) and hex wrench
(supplied) is attached to
the round hole in the stand
pedestal.
3.
Spread a thick, soft cloth (blanket, etc.) that will prevent
damage to the LCD panel on a stable flat surface where
the entire monitor can be placed, and place the monitor
with the LCD panel face down on the cloth.
4.
Place the stand on the monitor.
Hook the tab on the stand under the mounting plate (pre-
installed on monitor).
Tab
5.
Fasten the stand to the monitor with the supplied
screws (M4 x 10 with washers) (x4).
Use the supplied hex wrench.
• Landscape
Screw
(M4 x 10 with washers)
• Portrait
Operation buttons
Screw
(M4 x 10 with washers)
Front
Fixing pin
2
1
* If the monitor will be used in the portrait orientation, pull
out the fixing pin (1), and insert it into the hole (2) as
shown above.
* To remove the stand, place the monitor and stand as
shown above and remove the screws.
Caution
•
Adhere to the following when installing the monitor in its
portrait orientation. Failing to adhere to the following may
cause malfunctions.
- Install the monitor such that the operation buttons are
located on the top side.
- Set the MONITOR on the MONITOR menu to PORTRAIT.
(See page 20.)