Sharp PN-V600 Operation Manual - Page 47

Controlling with a PC, ■ Basic operation

Get Sharp PN-V600 PDF manuals and user guides View all Sharp PN-V600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

7. Specify the "DHCP CLIENT", "IP ADDRESS",etc. Controlling the Monitor with a PC (LAN) Controlling with a PC ■ Basic operation You use Internet Explorer on a PC on the LAN to control the monitor. 1. Launch Internet Explorer on the PC. 2. In the "Address" box, type "http://" followed by your monitor's IP address followed by "/", then press the Enter key. You can confirm the IP address with the DISPLAY function. DHCP CLIENT If your LAN has a DHCP server and you wish to obtain an address automatically, change this setting to "ON". To set the address manually, set this to "OFF". IP ADDRESS If the DHCP CLIENT is set to "OFF", specify an IP address. SUBNET MASK If the DHCP CLIENT is set to "OFF", specify the subnet mask. DEFAULT GATEWAY If the DHCP CLIENT is set to "OFF", specify the default gateway. If you are not using a default gateway, specify "0.0.0.0". 8. When the setting is changed, click [Apply]. 9. Check the message and click [OK]. 10. Exit Internet Explorer. 11. Restore the PC's IP address jotted in Step 6, "(2) Specifying the PC's IP address". 12. Connect the monitor and the PC to the LAN. Caution • Wait 10 seconds after clicking [OK] before proceeding. • When operating using the remote control unit or similar, click [Refresh]. TIPS • When manually setting the IP address, the IP address for secondary monitors connected by RS-232C can be automatically allocated. (See page 25.) When prompted to enter a user name and password, type the user name and password that you specified in the security settings (see page 49), and click [OK]. If you did not make any security settings, leave the spaces blank and click on [OK]. 3. You can check, control, and change the monitor's status and settings by clicking the menu items on the left side of the screen. • If you see an [Apply] button next to a setting, click it after you change that setting. TIPS • See pages 48 to 52 for details on each setting. • If you click [Refresh] before the screen finishes updating the current display, the "Server Busy Error" will appear. Wait for a moment before operating your monitor again. • You cannot operate the monitor while it is warming up. • If "DHCP CLIENT" is set to "ON", press DISPLAY on the remote control unit two times and then check the monitor's IP address. 47 E

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
47
E
47
7. Specify the “DHCP CLIENT”, “IP ADDRESS”,etc.
DHCP CLIENT
If your LAN has a DHCP server and you wish to obtain an
address automatically, change this setting to “ON”.
To set the address manually, set this to “OFF”.
IP ADDRESS
If the DHCP CLIENT is set to “OFF”, specify an IP
address.
SUBNET MASK
If the DHCP CLIENT is set to “OFF”, specify the subnet
mask.
DEFAULT GATEWAY
If the DHCP CLIENT is set to “OFF”, specify the default
gateway.
If you are not using a default gateway, specify “0.0.0.0”.
8. When the setting is changed, click [Apply].
9. Check the message and click [OK].
10
. Exit Internet Explorer.
11.
Restore the PC’s IP address jotted in Step 6, “(2)
Specifying the PC’s IP address”.
12.
Connect the monitor and the PC to the LAN.
Caution
•
Wait 10 seconds after clicking [OK] before proceeding.
•
When operating using the remote control unit or similar,
click [Refresh].
TIPS
•
When manually setting the IP address, the IP address
for secondary monitors connected by RS-232C can be
automatically allocated. (See page 25.)
Controlling with a PC
■ Basic operation
You use Internet Explorer on a PC on the LAN to control the
monitor.
1. Launch Internet Explorer on the PC.
2.
In the “Address” box, type “http://” followed by your monitor’s
IP address followed by “/”, then press the Enter key.
You can confirm the IP address with the DISPLAY function.
When prompted to enter a user name and password, type
the user name and password that you specified in the
security settings (see page 49), and click [OK].
If you did not make any security settings, leave the spaces
blank and click on [OK].
3. You can check, control, and change the monitor’s status
and settings by clicking the menu items on the left side of
the screen.
•
If you see an [Apply] button next to a setting, click it after
you change that setting.
TIPS
•
See pages 48 to 52 for details on each setting.
•
If you click [Refresh] before the screen finishes updating
the current display, the “Server Busy Error” will appear.
Wait for a moment before operating your monitor again.
•
You cannot operate the monitor while it is warming up.
•
If “DHCP CLIENT” is set to “ON”, press
DISPLAY
on the
remote control unit two times and then check the monitor’s
IP address.
Controlling the Monitor with a PC (LAN)