Singer One Instruction Manual 7 - Page 38
Check, Chart, Performance, Problems, Cuadro, Examen, Problemas, Ejecucion
View all Singer One manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 38 highlights
CHECK CHART FOR PERFORMANCE PROBLEMS GENERAL PROBLEMS Machine does not sew. * Foot control is not connected.- See page 7. * Power switch is turned off.- Turn on the switch. Machine lams/knocks. * Thread is caught in hook.- Clean hook (see page 35). * Needle is damaged.- Replace needle (see page 22). Fabric does not move. * Presser foot is not lowered - lower presser foot. * Stitch length is set at 0. - Set it at 1 to 4. STITCHING PROBLEMS Machine skips stitches. * Needle is not all the way up into needle clamp. - See page 22. * Needle is bent or blunt. - Replace needle (see page 22). * Machine is not threaded correctly. - See page 11. * Thread is caught in hook. - Clean hook (see page 35). Stitches are irregular. * Needle size is not correct for thread and fabric. - See page 22. * Machine is not threaded correctly. - See page 11. * Top thread tension is too loose. - See page 21. * Fabric is being pulled or pushed against machine feeding action. - Guide it gently. * Bobbin has not been wound evenly. - Rewind bobbin. Needle breaks. * Fabric is being pulled or pushed against machine feeding action. -Guide it gently. * Needle size is not correct for thread and fabric. - See page 22. * Needle is not all the way up into the needle clamp (See page 22). THREAD PROBLEMS Thread bunches. * Top and bobbin threads are not drawn back under presser foot before starting seam. - Draw both threads back under presser foot about 4 inches (10 cm) and hold until a few stitches are formed. Needle thread breaks. * Machine is not threaded correctly. - See page 11. * Top thread tension is too tight. - See page 21. * Needle is bent. - Replace needle (see page 22). * Needle size is not correct for thread and fabric - See page 22. Bobbin thread breaks. * Bobbin case is not threaded correctly. See page 10. * Lint accumulates in bobbin case or hook. - Remove lint (see page 35). Fabric puckers. * Top and bobbin thread tensions are too tight. - Adjust thread tensions (see page 21). * Stitch length is too long for sheer or soft fabric. - Shorten stitch length. 36 CUADRO DE EXAMEN PARA LOS PROBLEMAS DE EJECUCION PROBLEMAS GENERALES Maquina no cose. * El cord° electric° no este conectado (yea °eine 7). * El interruptor de energia no esta conectado. - Ponerio en la posicion LOW o HIGH. Maquina se atasca/rechina * El hilo esta enredado en la lanzadera. - Limpiar la lanzadera. * La aguja se rompe. - Reponer la aguja (yea pagina 22). La tela no se mueve. * El prensatelas no esta bajado perfectamente. - Bajar el prensatelas. * Longitud del punto es demasiado corto. - Prolonger la longitud del punto. * La placa de cubierta de transportador se instala. - Quitar la placa de cubierta de transportador. PROBLEMAS DE PUNTO La maquina salta puntos. * La aguja no esta fijada en la brida portaagujas (yea pagina 22). * La aguja esta torcida o obtusa. - Reponer la aguja (yea pagina 22). * La maquina no enhebra correctamente (yea pagina 11). Puntos son irrequlares. * El niimero de la aguja no es correcto para el hilo ni el material (yea pagina 22). * La maquina no enhebra correctamente (yea pagina 11). * La tension del hilo superior es demasiado floja (yea pagina 21). * El material esta tirado o empujado contra la accion de alimentaci0n. - Guiario suavemente. * La bobina no se ha devanado de un modo igual. - Redevanar la bobina. La aquia se remope. * El material esta tirado o empujado contra el accion de alimentacion. * El numero de la aguja no es correct° para el hilo ni el material (yea pagina 22). * La aguja no esta fijada en la brida portaagujas (yea pagina 22). PROBLEMAS DE HILO Los hilos se juntan * Los hilos superior e inferior no estan sacados debajo del prensatelas antes de empezar a coser, - Sacar ambos hilo debajo del prensatelas unos 10 cm y mantener hasta que se formen unos pocos puntos. La aquia se remope. * La maquina no enhebra correctamente (yea pagina 11). * La tension del hilo superior es demasiado apretada (yea pagina 21). * La aguja esta torcida. - Cambiar la agja (yea pagina 22). * El niimero de la aguja no es correcto para el hilo ni el material (yea pagina 22). El hilo inferior se rompe. * La capsula de portacanilla no enhebra correctamente (yea pagina 10). * Las hilas se acumulan en la capsula o en la lanzadera. - Quitarias (yea pagina 35). La tela no queda plana. * Las tensiones del hilo superior e inferior estan demasiado apretadas. - Ajustar las tensiones del hilo (yea pagina 21). * La longitud del punto es demasiado largo para material fino o suave - Acortar la longitud del punto.