Sony BKM-FW32 Operating Instructions - Page 20

Preparations for Using the Networking Function, Installing this device

Get Sony BKM-FW32 PDF manuals and user guides View all Sony BKM-FW32 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Preparations for Using the Networking Function You can connect this device to the network with a LAN cable (10BASE-T/100BASETX). This section describes the tasks required for using the networking function of this device. Installing this device Before installation • Before installation, make sure that the power to all the equipment is off. To turn the display completely off, press the 1 switch so that the display changes to standby mode, then disconnect the power cord from the wall outlet. • When you install this device, make sure that the flat panel display is locked and stable. Follow the steps below to install this device to the FWD series Flat Panel Display. 1 Remove the installed option adaptor or the panel cover. (Refer to either of the following illustrations that applies to your Display unit.) AUDIO OUT INPUT 2 R L OUT IN OUT IN AUDIO IN VIDEO S VIDEO R L AUDIO RGB / COMPONENT When the option slot is located on the left side of a Display unit* 1 2 1 * The location of the option slot differs depending on the model of the Display unit. If your Display unit has more than one option slot, install the device in a COM port, a slot used for the network. Refer to the Operating Instructions for the FWD series as well. VIDEO INPUT ADAPTOR GB6 Preparations for Using the Networking Function

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
GB
6
Preparations for Using the Networking Function
Preparations for
Using the
Networking
Function
You can connect this device to the network
with a LAN cable (10BASE-T/100BASE-
TX).
This section describes the tasks required for
using the networking function of this
device.
Installing this device
Before installation
•
Before installation, make sure that the
power to all the equipment is off. To turn
the display completely off, press the
1
switch so that the display changes to
standby mode, then disconnect the power
cord from the wall outlet.
•
When you install this device, make sure
that the flat panel display is locked and
stable.
Follow the steps below to install this device
to the FWD series Flat Panel Display.
1
Remove the installed option adaptor
or the panel cover. (Refer to either of
the following illustrations that applies
to your Display unit.)
INPUT 2
RGB / COMPONENT
AUDIO
L
R
AUDIO
OUT
VIDEO
S VIDEO
IN
OUT
IN
OUT
R
L
AUDIO IN
VIDEO INPUT ADAPTOR
1
2
1
When the option slot is located on
the left side of a Display unit*
*
The location of the option slot differs
depending on the model of the Display
unit. If your Display unit has more than
one option slot, install the device in a
COM port, a slot used for the network.
Refer to the Operating Instructions for the
FWD series as well.