Sony BVME250A User Manual (Operating Instructions - BVM-E250A / BVM-E170A) - Page 55

Color Temp Adj, Auto Adjust, To cancel/stop the adjustment, D-Cine, Preset 1, Preset D-Cine

Get Sony BVME250A PDF manuals and user guides View all Sony BVME250A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

Chapter 3 Menu Color Temp Adj Menu Auto Adjust Target Color Temp x y Target Luminance Contrast/Bright Hold Copy From Function and operation ([ ]: factory setting) Starts adjustment. When Auto Adjust is selected, not only the target color temperature but also other color temperature data are adjusted. Before automatic adjustment, select the value to use for the adjustment in following sequence. When you use the previously adjusted values for adjustment, select Auto Adjust in step 3 to start adjustment without performing step 1 and step 2. 1 Select the color temperature to be used in Target Color Temp. When Any is selected, enter the values of the CIE color system x and y coordinates. 2 Select Target Luminance and enter the value of the luminance (cd/m2) when the 100% white signal is input. 3 Select Auto Adjust. The cursor appears and flashes at the bottom left of the screen. (It may take some time until the automatic adjustment is completed.) To cancel/stop the adjustment Press the MENU button. Sets the adjustment value to be used from D93, D65, D61, D55, D-Cine or Any. Note Target Color Temp cannot be selected when the XYZ format signal is input. It is fixed to Calibration White. Enters the CIE color system x coordinate. Set to 0.265 to 0.350. Enters the CIE color system y coordinate. Set to 0.270 to 0.360. Enters the luminance (cd/m2) when the 100% white signal is input with the contrast and brightness set to the center. The following adjustable range is available, depending on the setting in the Picture Preset menu. Preset 1 to 5: 40 to 150 [100] Preset (D-Cine): 20 to 72 [48] Note The calibrated luminance does not guarantee an absolute value and may be different from the luminance detected by the probe. Sets the contrast and brightness to the adjusted value or the center value. The contrast value is fixed to 1000, and the brightness value is fixed to 000 during the automatic adjustment. Off: The contrast and brightness values are retained at the center value even after color temperature adjustment. [On]: The contrast and brightness values are returned to the previous values before color temperature adjustment. Copies the other color temperature. Note Use the controller with software version 1.6 or higher to use the Copy From function. 55 Adjustment Menu

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
55
Adjustment Menu
Chapter 3
Menu
Color Temp Adj
Auto Adjust
Starts adjustment.
When Auto Adjust is selected, not only the target color temperature but also other color
temperature data are adjusted.
Before automatic adjustment, select the value to use for the adjustment in following
sequence.
When you use the previously adjusted values for adjustment, select
Auto Adjust
in step
3
to
start adjustment without performing step
1
and step
2
.
1
Select the color temperature to be used in Target Color Temp.
When Any is selected, enter the values of the CIE color system x and y coordinates.
2
Select Target Luminance and enter the value of the luminance (cd/m
2
) when the
100% white signal is input.
3
Select Auto Adjust.
The cursor appears and flashes at the bottom left of the screen.
(It may take some time until the automatic adjustment is completed.)
To cancel/stop the adjustment
Press the MENU button.
Target Color Temp
Sets the adjustment value to be used from
D93
,
D65
,
D61
,
D55
,
D-Cine
or
Any
.
Note
Target Color Temp cannot be selected when the XYZ format signal is input. It is fixed to
Calibration White.
x
Enters the CIE color system x coordinate.
Set to
0.265
to
0.350
.
y
Enters the CIE color system y coordinate.
Set to
0.270
to
0.360
.
Target Luminance
Enters the luminance (cd/m
2
) when the 100% white signal is input with the contrast and
brightness set to the center.
The following adjustable range is available, depending on the setting in the Picture Preset
menu.
Preset 1
to
5
:
40
to
150 [100]
Preset (D-Cine)
:
20
to
72 [48]
Note
The calibrated luminance does not guarantee an absolute value and may be different from
the luminance detected by the probe.
Contrast/Bright Hold
Sets the contrast and brightness to the adjusted value or the center value.
The contrast value is fixed to 1000, and the brightness value is fixed to 000 during the
automatic adjustment.
Off:
The contrast and brightness values are retained at the center value even after color
temperature adjustment.
[On]:
The contrast and brightness values are returned to the previous values before
color temperature adjustment.
Copy From
Copies the other color temperature.
Note
Use the controller with software version 1.6 or higher to use the Copy From function.
Menu
Function and operation ([
]: factory setting)