Home » Sony Manuals » Audio Components » Sony CMT-NE3 » Manual Viewer

Sony CMT-NE3 Operating Instructions - Page 11

Creating your own, program - function button

Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

CD/MP3 - Play Creating your own program - Program Play You can make a program of up to 25 steps. You can synchro record the programed tracks onto a cassette tape (page 16). MP3 audio tracks cannot be played on CMTNE3. 1 Press CD to switch the function to CD. 2 Press PLAY MODE in stop mode repeatedly until "PGM" appears. 3 Press ./> repeatedly until the desired track number appears. Other operations To Do this Cancel Program Play Press PLAY MODE in stop mode repeatedly until both "PGM" and "SHUF(FLE)" disappears. Erase the program Press CLEAR in stop mode. Each time you press the button, a track is cleared from the end of the program. Add a track to the Perform steps 3 and 4 in stop end of the program mode. Tips • The program you made remains after Program Play finishes. To play the same program again, press N (or CD/NX on the unit). However, the program is cleared when you open the CD compartment. appears if the total program time exceeds 100 minutes, if you select a track whose number is 21 or over, or when you programed an MP3 audio track. Selected track number Total playing time (including selected track) For CMT-NE5 only: When programing an MP3, press ALBUM +/- repeatedly to select the album, then press ./> repeatedly until the desired track number appears. 4 Press ENTER on the remote. The track is programed. The program step number appears, followed by the last programed track number and total playing time. 5 To program additional tracks, repeat steps 3 and 4. 6 Press N. Program Play starts. 11GB

Section	Page
Table of Contents	3
How to use this manual	4
Playable discs	4
Hooking up the system	6
1 Connect the speakers.	6
2 Connect the FM and AM antennas.	6
3 For models with a voltage selector, set VOLTAGE SELECTOR to the local power line voltage. The v...	7
4 Connect the power cord to a wall outlet.	7
Setting the clock	8
1 Press ?/1 to turn on the system.	8
2 Press CLOCK/TIMER SET.	8
3 Press ./> repeatedly to set the hour.	8
4 Press ENTER.	8
5 Press ./> repeatedly to set the minute.	8
6 Press ENTER.	8
1 Press CLOCK/TIMER SET.	8
2 Press ./> until “CLOCK” appears, then press ENTER.	8
3 Do the same procedures as step 3 to 6 above.	8
Loading a disc	9
1 Press Z PUSH OPEN/CLOSE on the unit.	9
2 Place a disc with the label side up on the CD compartment.	9
3 Press Z PUSH OPEN/CLOSE on the unit again to close the lid of the CD compartment.	9
Playing a disc	9
1 Press CD to switch the function to CD.	9
2 Press PLAY MODE in stop mode repeatedly until the mode you want appears.	9
3 Press N.	9
Playing repeatedly	10
Creating your own program	11
1 Press CD to switch the function to CD.	11
2 Press PLAY MODE in stop mode repeatedly until “PGM” appears.	11
3 Press ./> repeatedly until the desired track number appears.	11
4 Press ENTER on the remote.	11
5 To program additional tracks, repeat steps 3 and 4.	11
6 Press N.	11
Presetting radio stations	12
1 Press TUNER/BAND repeatedly to select “FM” or “AM”.	12
2 Press TUNING MODE repeatedly until “AUTO” appears in the display.	12
3 Press +/– (or TUNING +/– on the unit).	12
4 Press TUNER MEMORY.	12
5 Press +/– (or TUNING +/– on the unit) repeatedly to select the desired preset number.	12
6 Press ENTER.	12
7 Repeat steps 3 through 6 to preset other stations.	12
1 Press TUNER/BAND repeatedly to select “FM” or “AM”.	12
2 Press TUNING MODE on the unit repeatedly until “AUTO” and “PRESET” disappear from the display.	12
3 Press +/– (or TUNING +/– on the unit) repeatedly to tune in the desired station.	12
4 Press TUNER MEMORY.	12
5 Press +/– (or TUNING +/– on the unit) repeatedly to select the desired preset number.	12
6 Press ENTER.	12
7 Repeat steps 3 through 6 to preset other stations.	12
Listening to the radio	13
1 Press TUNER/BAND repeatedly to select “FM” or “AM”.	13
2 Press TUNING MODE repeatedly until “PRESET” appears in the display.	13
3 Press +/– (or TUNING +/– on the unit) repeatedly to select the desired preset station.	13
1 Press TUNER/BAND repeatedly to select “FM” or “AM”.	13
2 Press TUNING MODE repeatedly until “AUTO” and “PRESET” disappear from the display.	13
3 Press +/– (or TUNING +/– on the unit) repeatedly to tune in the desired station.	13
Using the Radio Data System (RDS)	14
Loading a tape	15
1 Press Z PUSH OPEN on the unit.	15
2 Load a recorded/recordable tape into the cassette holder.	15
Playing a tape	15
1 Press TAPE to switch the function to TAPE.	15
2 Press N (or TAPE/N on the unit).	15
Recording your favorite CD tracks on a tape	16
1 Load a recordable tape.	16
2 Load a CD you want to record.	16
3 Press CD SYNCHRO.	16
4 Press z REC PAUSE/START.	16
Recording on a tape manually	16
1 Load a recordable tape.	16
2 Select the desired source to record.	16
3 Press z REC PAUSE/START.	16
4 Press z REC PAUSE/START, then start playing the desired source to record.	16
Adjusting the sound	17
1 Press EQ (or BASS/TREBLE on the unit) repeatedly to select “BASS” or “TREBLE”.	17
2 Press ./> (or TUNING +/– on the unit) repeatedly to adjust the level while “BASS” or “TREBLE” a...	17
Falling asleep to music	17
Waking up to music	18
1 Prepare the sound source you want to play.	18
2 Adjust the volume.	18
3 Press CLOCK/TIMER SET.	18
4 Press ./> repeatedly until “PLAY” appears, then press ENTER.	18
5 Set the time to start playing.	18
6 Set the time to stop playing following the same procedure as step 5.	18
7 Press ./> repeatedly until the desired sound source appears.	18
8 Press ENTER.	18
9 Press ?/1 to turn off the system.	18
Timer recording radio programs	19
1 Tune in the preset radio station (see “Listening to a preset station” on page13).	19
2 Press CLOCK/TIMER SET.	19
3 Press ./> repeatedly until “REC” appears, then press ENTER.	19
4 Set the time to start recording.	19
5 Set the time to stop recording following the same procedure as step 4.	19
6 Load a recordable tape.	19
7 Press ?/1 to turn off the system.	19
Turning off the display	20
Viewing information about the disc in the display	20
Hooking up optional components	21
1 Connect audio cords. See the illustration above.	21
2 Press FUNCTION repeatedly until “MD” appears. Start playing the connected component.	21
1 Connect audio cords.	21
2 Start recording manually. See “Recording on a tape manually” on page16.	21
Problems and remedies	22
1 Make sure the power cord and speaker cords are correctly and firmly connected.	22
2 Find your problem in the troubleshooting checklist below and take the indicated corrective action.	22
1 Disconnect the power cord.	24
2 Reconnect the power cord.	24
3 Press ?/1 to turn on the system.	24
4 Press x, ?/1 and turn volume to the left at the same time.	24
Messages	24
Precautions	26
On operating voltage	26
On safety	26
On placement	26
On heat buildup	26
On operation	26
Notes on discs	26
Cleaning the cabinet	26
To save a tape permanently	27
Before placing a cassette in the tape deck	27
When using a tape longer than 90minutes	27
Cleaning the tape heads	27
Demagnetizing the tape heads	27
Specifications	27