Sony DR-GA500 Operating Instructions - Page 19

To adjust the volume level from the sound device, GAIN CONTROL, To set the system to enter

Get Sony DR-GA500 - Digital Surround Headset System PDF manuals and user guides
UPC - 027242806146
View all Sony DR-GA500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

To adjust the volume level from the sound device (GAIN CONTROL) The GAIN CONTROL adjusts the volume according to the rated output of the sound device (initial setting is "8"). Increase the GAIN CONTROL more than "8" if the output is low, even when the volume of the sound device is maximized. And if sound is distorted, decrease the volume level of the output on the sound device. Rear panel of the processor Rotate left to decrease the level Rotate right to increase the level Sound device rated output More than 2Vrms 2Vrms Less than 2Vrms GAIN CONTROL level Adjust the GAIN CONTROL level to "8," and then adjust the audio output device to lower the sound. This processor is calibrated for 2Vrms standard output to the sound device when the GAIN CONTROL is set to "8." "8" - "10," the GAIN CONTROL level adjust for the louder volume. To set the system to enter the standby mode automatically (AUTO STANDBY function) The processor enters the standby mode automatically if the processor does not input sound for about 30 minutes. You can turn the AUTO STANDBY function ON/OFF by the AUTO STANDBY switch. Rear panel of the processor Position of switch ON OFF OFF ON AUTO STANDBY Effect The AUTO STANDBY function will work. Turn on the system again by pressing the  /  (on / standby) switch. The AUTO STANDBY function will not work. Operation 19GB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
19
GB
Operation
To adjust the volume level from the sound device
(GAIN CONTROL)
The GAIN CONTROL adjusts the volume according to the rated output of the sound device
(initial setting is “8”). Increase the GAIN CONTROL more than “8” if the output is low, even
when the volume of the sound device is maximized. And if sound is distorted, decrease the
volume level of the output on the sound device.
Rear panel of the processor
Rotate left to
decrease the
level
Rotate right
to increase
the level
Sound device
rated output
GAIN CONTROL level
More than 2Vrms
Adjust the GAIN CONTROL level to “8,” and then adjust the audio output device
to lower the sound.
2Vrms
This processor is calibrated for 2Vrms standard output to the sound device when
the GAIN CONTROL is set to “8.”
Less than 2Vrms
“8” - “10,” the GAIN CONTROL level adjust for the louder volume.
To set the system to enter the standby mode automatically
(AUTO STANDBY function)
The processor enters the standby mode automatically if the processor does not input sound for
about 30 minutes.
You can turn the AUTO STANDBY function ON/OFF by the AUTO STANDBY switch.
OFF
AUTO STANDBY
ON
Rear panel of the processor
Position of switch
Effect
ON
The AUTO STANDBY function will work. Turn on the system again by pressing
the
/
(on / standby) switch.
OFF
The AUTO STANDBY function will not work.