Sony HCD-GX8800 Operating Instructions - Page 23

Changing the spectrum, analyzer display, Adjusting the brightness, of the display, Changing

Page 23 highlights

Display Changing the spectrum analyzer display 1 Press AMP MENU. "SPECTRUM" appears in the display. 2 Press PUSH ENTER (or ENTER on the remote). The last selected spectrum appears. 3 Press < or , repeatedly to select the setting you want. The display changes as follows: SPECTRUM 1T t SPECTRUM 2 Y Y SPECTRUM OFF SPECTRUM 3 R R t SPECTRUM 4 T 4 Press PUSH ENTER (or ENTER on the remote). Adjusting the brightness of the display 1 Press AMP MENU. "SPECTRUM" appears. 2 Press M or m repeatedly to select "DIMMER", then press PUSH ENTER (ENTER on the remote). The last selected dimmer appears. 3 Press < or , repeatedly to select the setting you want. The display changes as follows: t DIMMER 1 y DIMMER 2 T tDIMMER 3T 4 Press PUSH ENTER (or ENTER on the remote). Changing the power illuminator You can select the power illuminator as you want. Press ILLUMINATION repeatedly to select the power illuminator you want when the system is turned on. Each time you press the button, the power illuminator mode changes cyclically as follows: PATTERN 1 t PATTERN 2 t PATTERN 3 t PATTERN 4 t PATTERN OFF Notes • When you turn VOLUME (or press VOL +/- on the remote), power illuminator shows the current volume level. • During the demonstration display, you can turn on or off power illuminator by pressing ILLUMINATION. Turning off the display - Power Saving Mode The demonstration display and the clock display can be turned off to minimize the amount of power consumed during standby mode (Power Saving Mode). Press DISPLAY repeatedly while the system is turned off until the demonstration display or the clock display disappears. To cancel Power Saving Mode Press DISPLAY once to show the demonstration display or twice to show the clock display. Each time you press the button, the system changes cyclically as follows: Demonstration1) t Clock2) t Power Saving Mode 1) The display changes and the indicators flashes even when the system is turned off. 2) "--.-- " appears in the display if you have not set the clock. continued 23GB Display MHC-GN800 4-244-569-11 (1)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36

MHC-GN800
4-244-569-
11
(1)
Display
23
GB
Display
Changing the spectrum
analyzer display
1
Press AMP MENU.
SPECTRUM
appears in the display.
2
Press PUSH ENTER (or ENTER on the
remote).
The last selected spectrum appears.
3
Press
<
or
,
repeatedly to select the
setting you want.
The display changes as follows:
4
Press PUSH ENTER (or ENTER on the
remote).
Adjusting the brightness
of the display
1
Press AMP MENU.
SPECTRUM
appears.
2
Press
M
or
m
repeatedly to select
DIMMER
, then press PUSH ENTER
(ENTER on the remote).
The last selected dimmer appears.
3
Press
<
or
,
repeatedly to select the
setting you want.
The display changes as follows:
4
Press PUSH ENTER (or ENTER on the
remote).
Changing the power
illuminator
You can select the power illuminator as you
want.
Press ILLUMINATION repeatedly to select
the power illuminator you want when the
system is turned on.
Each time you press the button, the power
illuminator mode changes cyclically as follows:
PATTERN 1
t
PATTERN 2
t
PATTERN 3
t
PATTERN 4
t
PATTERN OFF
Notes
When you turn VOLUME (or press VOL +/
on the
remote), power illuminator shows the current
volume level.
During the demonstration display, you can turn on
or off power illuminator by pressing
ILLUMINATION.
Turning off the display
Power Saving Mode
The demonstration display and the clock
display can be turned off to minimize the
amount of power consumed during standby
mode (Power Saving Mode).
Press DISPLAY repeatedly while the
system is turned off until the
demonstration display or the clock display
disappears.
To cancel Power Saving Mode
Press DISPLAY once to show the
demonstration display or twice to show
the clock display.
Each time you press the button, the system
changes cyclically as follows:
Demonstration
1)
t
Clock
2)
t
Power Saving
Mode
1)
The display changes and the indicators flashes even
when the system is turned off.
2)
--.--
appears in the display if you have not set the
clock.
DIMMER 2
T
t
DIMMER 3
T
continued
t
DIMMER 1
y
t
SPECTRUM 2
Y
SPECTRUM 3
R
SPECTRUM 1
T
Y
SPECTRUM OFF
R
t
SPECTRUM 4
T