Sony HCD-GX8800 Operating Instructions - Page 32

Messages - receiver

Page 32 highlights

Problems and remedies (continued) Tape Deck The tape does not record. • The tab has been removed from the tape. Cover the broken tab with adhesive tape. • The tape has reeled to the end. The tape does not record nor play or there is a decrease in sound level. • The tape heads are dirty. (See "Cleaning the tape heads" on page 34). • The record/playback heads are magnetized. (See "Demagnetizing the tape heads" on page 34). The tape does not erase completely. • The record/playback heads are magnetized. (See "Demagnetizing the tape heads" on page 34). There is excessive wow or flutter, or the sound drops out. • The capstans or pinch rollers are dirty. (See "Cleaning the tape heads" on page 34). Noise increases or the high frequencies are erased. • The record/playback heads are magnetized. (See "Demagnetizing the tape heads" on page 34). Tuner There is severe hum or noise ("TUNED" or "STEREO" flashes in the display). • Adjust the antenna. • The signal is too weak. Connect an external antenna. • Set "CD POWER OFF" by CD power manage function (page 15). A stereo FM program cannot be received in stereo. • Press FM MODE so that "MONO" disappears. If the system still does not operate properly after performing the above measures, reset the system as follows: 1 Unplug the power cord. 2 Plug the power cord back in. 3 Press x, AMP MENU and ?/1 at the same time. 4 Press ?/1 to turn on the system. The system is reset to factory settings. All the settings are cleared. Messages One of the following messages may appear or flash in the display during operation. CD Cannot Edit • You pressed EDIT before disc is ready. • You have programmed a disc with MP3 audio tracks. NO STEP • You have cleared all the tracks you programmed. OVER • You have reached the end of the disc while pressing M during playback or pause. No Disc • There is no disc on the disc tray. Push STOP! • You pressed PLAY MODE during playback. Step Full! • You tried to program 26 or more tracks (steps). TAPE No Tab • You cannot record the tape because the tab has been removed from the tape. No Tape • There is no tape in the tape deck. 32GB MHC-GN800 4-244-569-11 (1)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36

MHC-GN800
4-244-569-
11
(1)
32
GB
Tape Deck
The tape does not record.
The tab has been removed from the tape. Cover
the broken tab with adhesive tape.
The tape has reeled to the end.
The tape does not record nor play or there is a
decrease in sound level.
The tape heads are dirty. (See
Cleaning the tape
heads
on page 34).
The record/playback heads are magnetized. (See
Demagnetizing the tape heads
on page 34).
The tape does not erase completely.
The record/playback heads are magnetized. (See
Demagnetizing the tape heads
on page 34).
There is excessive wow or flutter, or the sound
drops out.
The capstans or pinch rollers are dirty. (See
Cleaning the tape heads
on page 34).
Noise increases or the high frequencies are erased.
The record/playback heads are magnetized. (See
Demagnetizing the tape heads
on page 34).
Tuner
There is severe hum or noise (
TUNED
or
STEREO
flashes in the display).
Adjust the antenna.
The signal is too weak. Connect an external
antenna.
Set
CD POWER OFF
by CD power manage
function (page 15).
A stereo FM program cannot be received in
stereo.
Press FM MODE so that
MONO
disappears.
If the system still does not operate
properly after performing the above
measures, reset the system as
follows:
1
Unplug the power cord.
2
Plug the power cord back in.
3
Press
x
, AMP MENU and
?/1
at the same
time.
4
Press
?/1
to turn on the system.
The system is reset to factory settings. All the
settings are cleared.
Messages
One of the following messages may appear or
flash in the display during operation.
CD
Cannot Edit
You pressed EDIT before disc is ready.
You have programmed a disc with MP3 audio
tracks.
NO STEP
You have cleared all the tracks you programmed.
OVER
You have reached the end of the disc while
pressing
M
during playback or pause.
No Disc
There is no disc on the disc tray.
Push STOP!
You pressed PLAY MODE during playback.
Step Full!
You tried to program 26 or more tracks (steps).
TAPE
No Tab
You cannot record the tape because the tab has
been removed from the tape.
No Tape
There is no tape in the tape deck.
Problems and remedies (continued)