Sony HCD-HDX267W Operating Instructions - Page 13

Connecting the AC power cord (mains lead), Changing the color system (PAL or NTSC) - model

Get Sony HCD-HDX267W - Dvd/receiver Component For Home Theater System PDF manuals and user guides View all Sony HCD-HDX267W manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Getting Started - BASIC - To connect the FM wire antenna (aerial) Connect the FM wire antenna (aerial) to the FM 75 Ω COAXIAL jack. FM wire antenna (aerial) (supplied) FM wire antenna (aerial) (supplied) or FM 75 Ω COAXIAL jack FM 75 Ω COAXIAL jack Note • Be sure to fully extend the FM wire antenna (aerial). • After connecting the FM wire antenna (aerial), keep it as horizontal as possible. Tip • If you have poor FM reception, use a 75-ohm coaxial cable (not supplied) to connect the unit to an outdoor FM antenna (aerial) as shown below. Unit Outdoor FM antenna (aerial) 4 Connecting the AC power cord (mains lead) Before connecting the AC power cord (mains lead) of this unit to a wall outlet (mains), connect the speakers to the unit. Changing the color system (PAL or NTSC) (Asian, Australian, and Middle Eastern models only) Depending on the TV to be connected, you may be required to select either PAL or NTSC for the color system. The initial setting of the system for Australian and Middle Eastern models is PAL. The initial setting of the system for Asian models is NTSC. To change the color system 1 Turn off the system by pressing "/1. 2 Turn on the system by pressing "/1 while pressing X on the unit. Each time you perform this operation, the color system toggles between PAL and NTSC. "NTSC" lights up in the front display when the color system is set to NTSC. 13GB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
13
GB
Getting Started – BASIC –
To connect the FM wire antenna (aerial)
Connect the FM wire antenna (aerial) to the FM 75
Ω
COAXIAL jack.
Note
• Be sure to fully extend the FM wire antenna (aerial).
• After connecting the FM wire antenna (aerial), keep it as horizontal as possible.
Tip
• If you have poor FM reception, use a 75-ohm coaxial cable (not supplied) to connect the unit to an outdoor FM
antenna (aerial) as shown below.
4
Connecting the AC power cord (mains lead)
Before connecting the AC power cord (mains lead) of this unit to a wall outlet (mains), connect the
speakers to the unit.
Changing the color system (PAL or NTSC)
(Asian, Australian, and Middle Eastern models only)
Depending on the TV to be connected, you may be required to select either PAL or NTSC for the color
system.
The initial setting of the system for Australian and Middle Eastern models is PAL.
The initial setting of the system for Asian models is NTSC.
To change the color system
1
Turn off the system by pressing
"
/
1
.
2
Turn on the system by pressing
"
/
1
while pressing
X
on the unit.
Each time you perform this operation, the color system toggles between PAL and NTSC.
“NTSC” lights up in the front display when the color system is set to NTSC.
FM wire antenna (aerial)
(supplied)
FM 75
Ω
COAXIAL jack
or
FM wire antenna (aerial)
(supplied)
FM 75
Ω
COAXIAL jack
Outdoor FM antenna (aerial)
Unit