Sony HVRMRC1K Operating Instructions - Page 17

Menu organization (COMPUTER mode), DV-NTSC, DV-PAL, DRIVE, SETTING

Page 17 highlights

Menu organization (COMPUTER mode) root HDV DV-NTSC DV-PAL DRIVE SETTING TC FORMAT DV FILETYPE CAMERA NO AUTO NDF DF AVI RAW DV *Boldface settings are default settings. HDV Operate in the VIDEO mode. Set this mode when reading or writing HDV stream data on a CompactFlash in this unit using editing software. DV-NTSC Operate in the VIDEO mode. Set this mode when reading or writing DV (NTSC format) stream data on a CompactFlash in this unit using the editing software. DV-PAL Operate in the VIDEO mode. Set this mode when reading or writing DV (PAL format) stream data on a CompactFlash in this unit using the editing software. DRIVE Operate as an external removable media of the computer. (Default setting) SETTING You can set this when in VIDEO mode. Settings are reflected in setting in the VIDEO mode operation when connecting to a camcorder. For details about setting, refer to "Menu organization (VIDEO mode)." Notes • For the following cases, operate "Safety remove Device (for Windows)" or "Remove by putting the media icon into the trash (for Mac OS)" etc., and check that the access lamp turns off. - When switching the each modes DRIVE, HDV or DVNTSC, DV-PAL - When disconnecting the i.LINK cable from the computer - When turning off the power of this unit To recognize this unit again after these operations, disconnect i.LINK cable from the computer once, then reconnect it. • Depending on the video editing software, this unit may not be recognized without switching the mode before starting the software. • If you change the operation mode frequently, the computer and this unit may not communicate correctly. Switch the mode of this unit at intervals about 5 seconds or more. • HDV, DV-NTSC, and DV-PAL mode may not be recognized because of a limitation of the computer when switching them directly. If that situation occurs, disconnect this unit from the computer, then select the mode. • If the combination of the settings of the editing software (HDV/DV-NTSC, DV-PAL) and this unit are incorrect, images may be distorted or recognized incorrectly. 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31

17
HDV
Operate in the VIDEO mode. Set this mode when reading or
writing HDV stream data on a CompactFlash in this unit
using editing software.
DV-NTSC
Operate in the VIDEO mode. Set this mode when reading or
writing DV (NTSC format) stream data on a CompactFlash in
this unit using the editing software.
DV-PAL
Operate in the VIDEO mode. Set this mode when reading or
writing DV (PAL format) stream data on a CompactFlash in
this unit using the editing software.
DRIVE
Operate as an external removable media of the computer.
(Default setting)
SETTING
You can set this when in VIDEO mode.
Settings are reflected in setting in the VIDEO mode operation
when connecting to a camcorder.
For details about setting, refer to “Menu organization
(VIDEO mode).”
Menu organization (COMPUTER mode)
root
HDV
DV-NTSC
DV-PAL
DRIVE
SETTING
TC FORMAT
DV FILETYPE
CAMERA NO
AUTO
NDF
DF
AVI
RAW DV
*Boldface settings are default settings.
Notes
• For the following cases, operate “Safety remove Device (for
Windows)” or “Remove by putting the media icon into the
trash (for Mac OS)” etc., and check that the access lamp
turns off.
When switching the each modes DRIVE, HDV or DV-
NTSC, DV-PAL
When disconnecting the i.LINK cable from the computer
When turning off the power of this unit
To recognize this unit again after these operations,
disconnect i.LINK cable from the computer once, then
reconnect it.
• Depending on the video editing software, this unit may not
be recognized without switching the mode before starting
the software.
• If you change the operation mode frequently, the computer
and this unit may not communicate correctly. Switch the
mode of this unit at intervals about 5 seconds or more.
• HDV, DV-NTSC, and DV-PAL mode may not be
recognized because of a limitation of the computer when
switching them directly.
If that situation occurs, disconnect this unit from the
computer, then select the mode.
• If the combination of the settings of the editing software
(HDV/DV-NTSC, DV-PAL) and this unit are incorrect,
images may be distorted or recognized incorrectly.