Sony MHC-MDX10 Operating Instructions - Page 48

Messages, There is no sound., No Disc, No Tab, Not in Use, OFF TIME NG, PUSH SELECT, Push STOP

Get Sony MHC-MDX10 - Mini Hi-fi Component System PDF manuals and user guides View all Sony MHC-MDX10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

Optional components There is no sound. • Refer to General item "There is no sound." (page 42) and check the condition of the system. • Connect the component properly (page 12) while checking: - if the cords are connected properly. - if the cord plugs are firmly inserted all the way. • Turn on the connected component. • Refer to the operating instructions supplied with the connected component and start playing. To reset the system to factory settings If the system still does not operate properly after performing the above measures or other troubles not described above occur, reset the system as follows: Use the buttons on the unit for the operation. 1 Unplug the power cord. 2 Plug the power cord back in. 3 Press "/1 to turn on the system. 4 Press x, DELAY and "/1 at the same time. "COLD RESET" appears in the display. The system is reset to the factory settings. You need to readjust all the settings you made, such as the preset stations, clock and timer. Messages One of the following messages may appear or flash in the display during operation. Disc/ Tape/ Timer No Disc There is no disc on the disc tray or you have loaded a disc that cannot be played back on this system. No Tab You cannot record onto the tape because the tab has been removed from the tape. No Tape There is no tape in the tape deck. Not in Use You have pressed a button those operation is not allowed or invalid at that time. OFF TIME NG! The on time and off time of Play Timer or Recording Timer is the same. PUSH SELECT! You tried to set the clock or timer during timer operation. Push STOP! You have pressed PLAY MODE on the remote during playback. Reading The system is reading information of the disc. Some buttons are not available. NO STEP You have cleared all the steps you programmed. OVER You have reached the end of the disc while pressing M during playback or pause. Step Full! You tried to program more than 25 steps. 48GB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
48
GB
Optional components
There is no sound.
•
Refer to General item “There is no
sound.” (page 42) and check the
condition of the system.
•
Connect the component properly
(page 12) while checking:
– if the cords are connected properly.
– if the cord plugs are firmly inserted all
the way.
•
Turn on the connected component.
•
Refer to the operating instructions
supplied with the connected component
and start playing.
To reset the system to factory
settings
If the system still does not operate
properly after performing the above
measures or other troubles not described
above occur, reset the system as follows:
Use the buttons on the unit for the
operation.
1
Unplug the power cord.
2
Plug the power cord back in.
3
Press
"/1
to turn on the system.
4
Press
x
, DELAY and
"/1
at the
same time.
“COLD RESET” appears in the
display.
The system is reset to the factory settings.
You need to readjust all the settings you
made, such as the preset stations, clock
and timer.
Messages
One of the following messages may
appear or flash in the display during
operation.
Disc/ Tape/ Timer
No Disc
There is no disc on the disc tray or you
have loaded a disc that cannot be played
back on this system.
No Tab
You cannot record onto the tape because
the tab has been removed from the tape.
No Tape
There is no tape in the tape deck.
Not in Use
You have pressed a button those operation
is not allowed or invalid at that time.
OFF TIME NG!
The on time and off time of Play Timer or
Recording Timer is the same.
PUSH SELECT!
You tried to set the clock or timer during
timer operation.
Push STOP!
You have pressed PLAY MODE on the
remote during playback.
Reading
The system is reading information of the
disc. Some buttons are not available.
NO STEP
You have cleared all the steps you
programmed.
OVER
You have reached the end of the disc
while pressing
M
during playback or
pause.
Step Full!
You tried to program more than 25 steps.