Sony MZ-NHF800 Operating Instructions - Page 92

Symptom, Cause/Remedy, This is due to the MiniDisc system limitation. The recorder turns off 3

Page 92 highlights

Symptom Cause/Remedy The recorder does not work or works poorly. • The disc is damaged or does not contain proper recording or editing data. , Reinsert the disc. Rerecord the disc. If the error message still appears, replace it with another disc. • There is a built-in malfunction in the system. • While operating, the recorder received a mechanical shock, too much static, abnormal power voltage caused by lightning, etc. , Restart the operation as follows. 1 Disconnect all the power sources and the dedicated USB cable. 2 Leave the recorder for about 30 seconds. 3 Connect the power source. The display window • The recorder was disconnected from the power source. is not normal. , Let the recorder sit for a while, or disconnect the power source, reconnect it, and then press any of the operation buttons. When using with the AC power adaptor, the display window of the recorder will remain faintly lit for some time even after the recorder is stopped. • This is due to the MiniDisc system limitation. The recorder turns off 3 minutes after the recorder has stopped in order to allow the charging time to be calculated. The operation mode of the blank 60/74/ 80-minute standard disc differs from the mode following formatting or the mode selected in the SonicStage software. • When using a blank 60/74/80-minute standard disc in the recorder, the operation mode set in the "Disc Mode" menu is applied. , Use the "Disc Mode" menu to change the operation mode as desired. 92

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132

92
The recorder does
not work or works
poorly.
The disc is damaged or does not contain proper recording or editing
data.
,
Reinsert the disc. Rerecord the disc. If the error message still
appears, replace it with another disc.
There is a built-in malfunction in the system.
While operating, the recorder received a mechanical shock, too much
static, abnormal power voltage caused by lightning, etc.
,
Restart the operation as follows.
1
Disconnect all the power sources and the dedicated USB cable.
2
Leave the recorder for about 30 seconds.
3
Connect the power source.
The display window
is not normal.
The recorder was disconnected from the power source.
,
Let the recorder sit for a while, or disconnect the power source,
reconnect it, and then press any of the operation buttons.
When using with the
AC power adaptor,
the display window
of the recorder will
remain faintly lit for
some time even after
the recorder is
stopped.
This is due to the MiniDisc system limitation. The recorder turns off 3
minutes after the recorder has stopped in order to allow the charging
time to be calculated.
The operation mode
of the blank 60/74/
80-minute standard
disc differs from the
mode following
formatting or the
mode selected in the
SonicStage
software.
When using a blank 60/74/80-minute standard disc in the recorder, the
operation mode set in the “Disc Mode” menu is applied.
,
Use the “Disc Mode” menu to change the operation mode as
desired.
Symptom
Cause/Remedy