Symphonic WF803 Owner's Manual - Page 16

Setup, Automatic Channel Set Up

Page 16 highlights

SETUP AUTOMATIC CHANNEL SET UP VCR You can automatically program the tuner to scan only the channels you receive in your area. ¡Channel memory programming is NOT needed when you connect the VCR to a cable box or a satellite box as in "CONNECTING TO A TV WITHOUT A/V TERMINALS" on page 13. In this case, select channel 3 on your TV. Then, the channel you want to record or view may be selected at the cable box or satellite box. ¡If noise appears, change the RF output channel of the VCR to channel 4 by pressing PLAY for 3 seconds during playback. Then select the same channel (CH4) on your TV. ¡Follow the steps below once. Repeat only if there is a power failure or if the VCR is unplugged for more than 30 seconds. (In these cases, the programmed channels are erased.) ¡You must follow the steps below before attempting to play or record a video tape. If you want to play or record a video tape BEFORE programming the tuner, you can cancel it by pressing CLEAR/C.RESET. 1 You need to connect the antenna or cable to the VCR first. Then, connect the DVD /VCR power plug to a standard AC outlet. 2 Turn on the TV and set the TV to channel 3. ¡If noise appears, change the RF output channel of the VCR to channel 4 by pressing PLAY for 3 seconds during playback. Then select the same channel (CH4) on your TV. (See "RF OUTPUT CHANNEL" on page 13 for the detail.) 3 Turn on the VCR by pressing POWER. the POWER light will come on. 6 After scanning, the tuner stops on the low- est memorized channel. The TV screen returns to TV mode. ¡If "AUTO SET UP" appears on the TV screen again, check the cable connections. Press B once again and the VCR will begin preset again. TO SELECT A DESIRED CHANNEL You can select the desired channel by using CHANNEL (o/p) or by directly pressing Number on the remote control. Note for using the Number: ¡When selecting cable channels which are higher than 99, enter channel numbers as a three-digit number.(For example: 117, press 1,1,7) ¡You must precede single-digit channel numbers with a zero (For example: 02, 03, 04 and so on). TO PRESET THE CHANNELS AGAIN 1 Press MENU until the main menu appears. (If you have already set the clock, you only have to press it once. If not, you have to press it twice). 2 Select "CHANNEL SET UP" by pressing K or L. Then, press B. 3 Select "AUTO SET UP" by pressing K or L. Then, press B. ¡After scanning, the tuner stops on the lowest memo- rized channel. 4 Select the On Screen Language ("ENG- LISH", "FRANCAIS" or "ESPAÑOL") by pressing K or L. Then, press B. 5 Begin channel preset by pressing Bonce. The tuner scans and memorizes all active channels in your area. CH 01 ¡The VCR distinguishes between standard TV channels and cable AUTO SET UP channels. - 16 - EN 1L25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44

6
After scanning, the tuner stops on the low-
est memorized channel. The TV screen
returns to TV mode.
¡
If
AUTO SET UP
appears on the TV screen again,
check the cable connections. Press
B
once again and
the VCR will begin preset again.
16
EN
1L25
AUTOMATIC CHANNEL SET UP
SETUP
You can automatically program the tuner to scan only
the channels you receive in your area.
¡
Channel memory programming is NOT needed
when you connect the VCR to a cable box or a satel-
lite box as in "CONNECTING TO A TV WITHOUT
A/V TERMINALS" on page 13. In this case, select
channel 3 on your TV. Then, the channel you want to
record or view may be selected at the cable box or
satellite box.
¡
If noise appears, change the RF output channel of
the VCR to channel 4 by pressing PLAY for 3 sec-
onds during playback.
Then select the same chan-
nel (CH4) on your TV.
¡
Follow the steps below once. Repeat only if there
is a power failure or if the VCR is unplugged for
more than 30 seconds. (In these cases, the pro-
grammed channels are erased.)
¡
You must follow the steps below before attempting
to play or record a video tape. If you want to play
or record a video tape BEFORE programming the
tuner, you can cancel it by pressing
CLEAR/C.RESET.
1
You need to connect the antenna or cable to
the VCR first. Then, connect the DVD /VCR
power plug to a standard AC outlet.
2
Turn on the TV and set the TV to channel 3.
¡
If noise appears, change the RF output channel of
the VCR to channel 4 by pressing PLAY for 3 sec-
onds during playback.
Then select the same chan-
nel (CH4) on your TV. (See
RF OUTPUT
CHANNEL
on page 13 for the detail.)
3
Turn on the VCR by pressing POWER. the
POWER light will come on.
4
Select the On Screen Language (
ENG-
LISH
,
FRANCAIS
or
ESPA
Ñ
OL
) by pressing
K
or
L
. Then, press
B
.
5
Begin channel preset by pressing
B
once.
The tuner scans and memorizes all active
channels in your area.
¡
The VCR distinguishes between
standard TV channels and cable
channels.
VCR
TO SELECT A DESIRED CHANNEL
You can select the desired channel by using CHAN-
NEL (
o
/
p
) or by directly pressing Number on the
remote control.
Note for using the Number:
¡
When selecting cable channels which are higher
than 99, enter channel numbers as a three-digit num-
ber.(For example: 117, press 1,1,7)
¡
You must precede single-digit channel numbers with
a zero (For example: 02, 03, 04 and so on).
TO PRESET THE CHANNELS AGAIN
1
Press MENU until the main menu appears.
(If you have already set the clock, you only
have to press it once. If not, you have to
press it twice).
2
Select
CHANNEL SET UP
by pressing
K
or
L
. Then, press
B
.
3
Select
AUTO SET UP
by pressing
K
or
L
.
Then, press
B
.
¡
After scanning, the tuner stops on the lowest memo-
rized channel.
AUTO SET UP
CH 01