TEAC CG-10M Owners Manual - Page 5

Before use, Maintenance, Note about pinpoint feet

Get TEAC CG-10M PDF manuals and user guides View all TEAC CG-10M manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

Before use Maintenance VVPlacement precautions Wipe dirt from the top cover and other panel surfaces using a soft oo When installing this unit, leave a little space (at least 3 cm or 1") cloth that has been slightly dampened with a diluted neutral cleanser. Do not wipe with chemical cleaning cloths, thinner or other chemi- between it and walls and other devices in order to allow good cal agents. Doing so could damage the surface. heat dissipation. If you put it in a rack, take precautions to prevent overheating by VVFor your safety, disconnect the power cord from EN leaving at least 5 cm (2") open above the top of the unit and at least 10 cm (4") open behind the unit. the outlet before cleaning. Failure to provide these gaps could cause heat to build up inside and result in fire. oo Do not install this unit in a location that could become hot. This includes places that are exposed to direct sunlight or near a radiator, heater, stove or other heating equipment. Moreover, do not place it on top of an amplifier or other equipment that generates heat. Doing so could cause discoloration, deformation or malfunction. oo Place the unit in a stable location near the audio system that you will use with it. oo Do not move the unit during use. oo The voltage supplied to the unit should match the voltage printed on the rear panel. If you are in any doubt regarding this matter, consult an electrician. oo Do not open the body of the unit as this might result in damage to the circuitry or cause electric shock. If a foreign object should get into the unit, contact your dealer. oo Do not place anything, not even CDs, CD-Rs, LP records or cassette tapes, on top of the unit. Doing so could cause damage. oo When removing the power plug from an outlet, always pull directly on the plug; never yank on the cord itself. Note about pinpoint feet High-precision metal pinpoint feet are attached firmly to the bottom plate of this unit. The stands for these feet are loose, but when the unit is placed in position, it is supported by these pinpoint feet, which will effectively disperse vibrations. Chassis Pinpoint foot (metal) Foot-stand (metal) Screws that attach foot-stand oo Apply the included pads to the bottoms of the foot-stands to avoid scratching the surface where the unit is placed. 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
EN
5
V
Placement precautions
o
When installing this unit, leave a little space (at least 3 cm or 1
"
)
between it and walls and other devices in order to allow good
heat dissipation.
If you put it in a rack, take precautions to prevent overheating by
leaving at least 5 cm (2
"
) open above the top of the unit and at
least 10 cm (4
"
) open behind the unit.
Failure to provide these gaps could cause heat to build up inside
and result in fire.
o
Do not install this unit in a location that could become hot.
This includes places that are exposed to direct sunlight or near
a radiator, heater, stove or other heating equipment. Moreover,
do not place it on top of an amplifier or other equipment that
generates heat. Doing so could cause discoloration, deformation
or malfunction.
o
Place the unit in a stable location near the audio system that you
will use with it.
o
Do not move the unit during use.
o
The voltage supplied to the unit should match the voltage
printed on the rear panel. If you are in any doubt regarding this
matter, consult an electrician.
o
Do not open the body of the unit as this might result in damage
to the circuitry or cause electric shock. If a foreign object should
get into the unit, contact your dealer.
o
Do not place anything, not even CDs, CD-Rs, LP records or cas-
sette tapes, on top of the unit. Doing so could cause damage.
o
When removing the power plug from an outlet, always pull
directly on the plug; never yank on the cord itself.
Note about pinpoint feet
High-precision metal pinpoint feet are attached firmly to the bot-
tom plate of this unit.
The stands for these feet are loose, but when the unit is placed in
position, it is supported by these pinpoint feet, which will effectively
disperse vibrations.
Chassis
Pinpoint foot (metal)
Foot-stand (metal)
Screws that attach
foot-stand
o
Apply the included pads to the bottoms of the foot-stands to
avoid scratching the surface where the unit is placed.
Before use
Wipe dirt from the top cover and other panel surfaces using a soft
cloth that has been slightly dampened with a diluted neutral cleanser.
Do not wipe with chemical cleaning cloths, thinner or other chemi-
cal agents. Doing so could damage the surface.
V
For your safety, disconnect the power cord from
the outlet before cleaning.
Maintenance