Home » TEAC Manuals » Audio Mixers » TEAC DP-24 » Manual Viewer

TEAC DP-24 DP-24 Owner's Manual - Page 47

DIGITAL TRIM setting (Track only), Built-in Send Effects and External Effects

Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

6 - Basic Recording Use the SELECT button of each track to select the desired track. Press the SOURCE button of each INPUT to change the input. Use the HIGH, MID, and LOW GAIN knobs to adjust the gain. Use the HIGH, MID, and LOW FREQ knobs to adjust the frequency. Use the MID Q knob to set the MID FREQ bandwidth. Setting range: 0.25 to 16 (Default: 0.5) Press the EQUALIZER ON/OFF button to turn the equalizer on or off. NOTE •• "Q" refers to the center frequency of the equalizer divided by the bandwidth. A high Q value reduces the cut and/or boost applied to the frequencies. Depending on the equalizer setting, the graph at the top of the screen changes. •• If you press the F1 (EQ FLAT) button, all the settings on the open Mixer screen will be restored to their default values. 3. After making the settings, press the HOME button to return to the Home screen. DIGITAL TRIM setting (Track only) 1. Use the CURSOR (5/b/g/t) buttons to move the cursor to the DIGITAL TRIM display area. Effect send indication 2. Turn the JOG/DATA dial to set the effect. Options: OFF (default), PRE, POST PRE This sends the track pre-fader signal to the effect send bus. The effect send signal level is not affected by the track fader. POST This sends the track post-fader signal to the effect send bus. The effect send signal level is affected by the track fader. 3. Use the SEND EFF 1/EFF 2 to adjust the send level. Setting range: 0 to 127 (Default: 0) 4. Use the SEND MASTER 1/MASTER 2 to adjust the send master level. Setting range: 0 to 127 (Default: 0) Setting built-in effects 1. Use the CURSOR (5/b/g/t) buttons to move the cursor to the INSERT EFFECT display area. DIGITAL TRIM indication 2. Turn the JOG/DATA dial to set the value. Setting range: -42dB to +6dB (Default: 0dB) NOTE Normally, set to 0dB, but if you want to boost the equalizer, we recommend that you lower the gain to prevent digital clipping. Built-in Send Effects and External Effects This unit has two external effect send systems (EFF 1 and EFF 2) and a built-in effect send function (INSERT EFFECT). You can adjust send levels for each track. For details about the built-in send effects, see "Send effects" on page 65. 1. Use the CURSOR (5/b/g/t) buttons to move the cursor to the EFFECT item on the SEND EFF 1/ EFF 2 display area. INSERT EFFECT indicator 2. Turn the JOG/DATA dial to set the built-in effect. Options: OFF: INSERT EFFECT indicator unlit (default) ON: INSERT EFFECT indicator lit 47 TASCAM DP-24

Section	Page
1 – Introduction	8
Features	8
Items included with the product	8
Conventions used in this manual	8
Intellectual property rights	9
Precautions for placement and use	9
Beware of condensation	9
Cleaning the unit	9
About SD cards	9
Precautions for use	10
About CDs (Compact Discs)	10
Precautions for use	10
About CD-R and CD-RW discs	10
2 - Quick Guide	12
Playback and mixing	12
Preparation	12
Listening to the demo song	13
Recording and mastering	14
Creating a new song	14
Connecting and setting the input sources	15
Setting the guitar as the recording source for TRACK 1	15
Adjusting and monitoring the input level	15
Recording a guitar to TRACK 1	16
Playing back the recording	16
Recording a guitar to TRACK 2	16
Recording a vocal to TRACK 3	17
Mixing the tracks	18
Mastering a recording	19
Creating an audio CD with the master file	21
Inserting a CD	21
Writing to a CD-R/CD-RW	22
Ejecting a CD	23
Shutting down	23
3 – Names and Functions of Parts	24
Top panel	24
Front panel	28
Rear panel	29
Home screen	30
Menu structure	31
Screen operations	32
4 – Preparation	34
Inserting and removing SD cards	34
Inserting an SD card	34
Removing the card	34
About write-protected SD cards	34
Powering the unit	34
Start-up & Shutdown	35
Starting up the unit	35
Shutting down	35
Setting the date and time	35
Preparing an SD card for use	36
Recorder modes	36
Connecting other equipment	36
Front panel	36
Rear panel	37
Adjusting the contrast	37
5 - Song Management	38
Editing names	38
Loading a song	38
Creating a new song	38
Saving a song	39
Viewing song information	40
Copying songs	40
Erasing songs	41
Protecting songs	41
Deleting unnecessary audio data from a song	42
Changing a song name	43
6 - Basic Recording	44
Selecting the input sources	44
Assigning inputs	44
Assigning to a mono track	44
Assigning to a stereo track	44
Assigning to a stereo bus	44
Checking the assignment	45
Canceling an assignment	45
Using phantom power	45
Monitoring	45
Monitor selection	45
OL indicators and level meters	46
Setting the Mixer screen	46
Using EQ (equalizer)	46
DIGITAL TRIM setting (Track only)	47
Built-in Send Effects and External Effects	47
Setting built-in effects	47
Setting the stereo position	48
Changing the signal phase	48
Checking the fader level	48
Solo	48
Muting tracks	48
Rehearsing the recording	49
Making the first recording	49
Multitrack recording	50
Setting the tracks for recording	50
Setting track pan and level	50
Input selection and assignment	50
Setting input levels	50
Recording	50
Undoing an operation	50
Setting the undoing feature	50
Undoing the last operation (single undo)	51
Undoing previous operations (multi-undo)	51
7 - Recorder Functions	52
Punching in and out	52
Using a foot switch to punch in/out	52
Setting the foot switch	52
Bouncing tracks	53
Performing the track bouncing	53
Checking the result	53
Direct Location Function	54
Locating directly a specified time	54
Locating directly a specified measure/beat	54
Location marks	54
Setting a location mark	54
Skipping to location marks	55
Deleting a location mark	55
Returning to zero (TO ZERO) and returning to last recording position (TO LAST REC)	55
Fast forward/rewind search	55
Jog positioning	55
Viewing the track's waveform	55
Listening to the track sounds	55
Repeat playback	56
Setting IN/OUT points	56
Using repeat playback	56
Moving back a few seconds for replay (jump back playback)	56
Checking cueing points (preview)	57
Auto punch in/out	57
Setting punch in/out points	58
Checking punch in/out points	58
Rehearsing punch in/out	58
Performing auto punch in/out	59
Checking a take	59
Virtual tracks	59
8 - Track Editing	60
Overview of track editing	60
Editing points	60
Basic editing procedures	60
Explanation of items	60
COPY/PASTE	61
COPY/INSERT	61
MOVE/PASTE	62
MOVE/INSERT	62
OPEN (Insert Silence)	62
CUT (Remove Part)	62
SILENCE (Erase Part)	63
CLONE TRACK (Track Duplication)	63
CLEAN OUT (Delete Track)	63
9 - Using Built-In Effects	64
Dynamic effects	64
Inserting a dynamic effect	64
Editing a dynamic effect	64
Guitar effects	64
Inserting a guitar effect	64
Editing guitar effects	65
Calling effects from the guitar effect library	65
Saving guitar effects in the library	65
Send effects	65
Using send effects	65
Editing send effects	65
Calling the send effect library	66
Saving send effects in the library	66
10 - Mixing Down and Mastering Tracks	68
Mixing down tracks	68
Levels and balance	68
Fader group	68
Stereo position (panning)	68
TRACK EQ (equalizer)	68
Send effects	69
Creating a master file	69
Setting the start and end points	69
Creating a master file	70
Exiting Mixdown mode	70
Checking the master file	70
Ending master file checking	71
Finishing up a master file (mastering)	71
Mastering procedures	71
Using the mastering EQ (equalizer)	71
Using mastering compression	72
Using normalize	73
Using the noise shaper (Noise Shaped Dithering)	73
Exiting Mastering mode	73
11 - Various Other Functions	74
Metronome	74
MIDI Sync	74
MIDI remote control	75
Tuner function	75
Setup (PREFERENCE)	76
Auto Monitor	76
Restoring the initial preference settings	77
Viewing information	77
12 - SD Card Management	78
Quick formatting an SD card	78
Full formatting an SD card	79
13 - Exchanging Data with a Computer	80
Operating system requirements	80
Connecting to a computer	80
Disconnecting	81
Track import and export	82
Importing tracks	82
Exporting tracks	83
Deleting files from the AudioDepot folder	83
14 - Using CDs	84
Using the CD drive	84
Preparations before using CDs with this unit	84
Types of CDs that can be used with this unit	84
Loading and ejecting CDs	85
Loading a CD	85
Ejecting a CD	86
Forcing disc ejection	86
Playing back an Audio CD	86
Creating an Audio CD	87
Using Disc At Once	87
Using Track At Once	88
Using LIVE WRITER	89
Finalizing a CD	90
Importing songs from an Audio CD	90
Erasing a CD-RW	91
Media Compatibility Table	91
15 – Troubleshooting	92
16 – Messages	93
General messages	93
CD mode messages	95
CD-related error messages	96
17 – Specifications	97
Ratings	97
Input/output ratings	97
Analog audio input/output ratings	97
Control input/output ratings	97
Audio performance	97
Operating requirements	97
Dimensional drawings	98
General	98
Block diagram	99
Level diagram	100
18 – Appendix	101
MIDI Control Change message	101
Mixer control change parameters	101
MIDI Program Change message	102
Dynamic effects	102
Preset libraries of the send effects	102
Preset libraries of the guitar effects	102
MIDI Implementation Chart	103

Match case Limit results 1 per page

TASCAM DP-24

6 - Basic Recording

Use the

SELECT

button of each track to select the

desired track.

Press the

SOURCE

button of each

INPUT

to change the

input.

Use the

HIGH

MID

, and

LOW

GAIN

knobs to adjust

the gain.

Use the

HIGH

MID

, and

LOW

FREQ

knobs to adjust

the frequency.

Use the

MID

knob to set the

MID FREQ

bandwidth.

Setting range:

0.25

(Default:

0.5

)

Press the

EQUALIZER

ON/OFF

button to turn the

equalizer on or off.

NOTE

"Q"

•

refers to the center frequency of the equalizer

divided by the bandwidth. A high

value reduces

the cut and/or boost applied to the frequencies.

Depending on the equalizer setting, the graph at the

top of the screen changes.

If you press the

•

(

EQ FLAT

) button, all the settings

on the open Mixer screen will be restored to their

default values.

After making the settings, press the HOME button

to return to the Home screen.

DIGITAL TRIM setting (Track only)

Use the CURSOR (

) buttons to move the

cursor to the

DIGITAL TRIM

display area.

Turn the JOG/DATA dial to set the value.

Setting range:

-42dB

+6dB

(Default:

0dB

)

NOTE

Normally, set to

0dB

, but if you want to boost the

equalizer, we recommend that you lower the gain to

prevent digital clipping.

Built-in Send Effects and External

Effects

This unit has two external effect send systems (

EFF 1

and

EFF 2

) and a built-in effect send function (INSERT EFFECT).

You can adjust send levels for each track. For details about

the built-in send effects, see "Send effects" on page 65.

Use the CURSOR (

) buttons to move the

cursor to the EFFECT item on the

SEND EFF 1/

EFF 2

display area.

Turn the JOG/DATA dial to set the effect.

Options:

OFF

(default),

PRE

POST

PRE

This sends the track pre-fader signal to the effect

send bus. The effect send signal level is not affected

by the track fader.

POST

This sends the track post-fader signal to the effect

send bus. The effect send signal level is affected by

the track fader.

Use the SEND EFF 1/EFF 2 to adjust the send level.

Setting range:

127

(Default:

)

Use the SEND MASTER 1/MASTER 2 to adjust the

send master level.

Setting range:

127

(Default:

)

Setting built-in effects

Use the CURSOR (

) buttons to move the

cursor to the

INSERT EFFECT

display area.

Turn the JOG/DATA dial to set the built-in effect.

Options:

OFF:

INSERT EFFECT

indicator unlit (default)

ON:

INSERT EFFECT

indicator lit

Effect send

indication

INSERT EFFECT

indicator

DIGITAL TRIM

indication