Home » TEAC Manuals » Audio Mixers » TEAC DP-24 » Manual Viewer

TEAC DP-24 DP-24 Owner's Manual - Page 58

Setting punch in/out points, Rehearsing punch in/out, Press the RECORD

Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

7 - Recorder Functions Setting punch in/out points There are two methods to set the punch in/out points. LAST REC: This option sets the start and end points of the last recording (or recording rehearsal) as the punch in/out points. The display returns to the Home screen, and Auto Punch appears on the top of the screen. IN - OUT: This option sets the IN point and the OUT point as the punch in/out points. The first of these points will be used as the punch in point, and the second as the punch out point. The display returns to the Home screen, and Auto Punch appears on the top of the screen. 1. When the recorder is stopped, press the HOME button to open the Home screen. 2. Press the REC button for the track that you want to punch in/out automatically. 3. Press the AUTO PUNCH button to open the AUTO PUNCH screen. NOTE If you press the AUTO PUNCH button without any tracks in recording standby, even after that you can press the REC button of any track to put it into recording standby. 4. Use the CURSOR (5/b) buttons to select (blue highlight) MODE, PREROLL or POSTROLL, and then use the JOG/DATA dial to select the value. MODE: LAST REC or IN-OUT PREROLL: 1.0 to 9.9 sec POSTROLL: 1.0 to 9.9 sec After setting MODE, PREROLL, and POSTROLL, press the F4 (t) button. You can press the AUTO PUNCH button to return to the Home screen without entering Auto Punch In/Out mode. Checking punch in/out points When punch in/out points are set, you can confirm the setting by pressing the PLAY (7) button. The playback starts from the pre-roll point to the post-roll point. If you want to change the punch in/out points, locate the desired points and set the punch in/out points again. If there are no problems about punch in/out points, preroll time, and post-roll time perform the rehearsal, as described below. Rehearsing punch in/out You can rehearse before performing punch in/out. In the rehearsal, the monitor operates the same way as for the actual recording, but the recording is not performed. 1. When the AUTO PUNCH button is lit and one of the tracks is in recording standby, press the REHEARSE button. The REHEARSE button becomes lit. 2. Press the RECORD (0) button. Auto punch in/out rehearsal starts. •• Playback starts from the pre-roll point. You can monitor both the track playback signal and the input source signal. •• When the punch in point is reached, the monitoring changes to input source signal only, and the RECORD (0) button starts flashing (to indicate this is a rehearsal). •• When the punch out point is reached, the monitoring of both the track playback signal and input source signal starts, and the RECORD (0) button becomes unlit. •• Playback continues until the post-roll point and stops. Before starting your rehearsal, you can press the REPEAT button (so that all three AUTO PUNCH, REHEARSE, and REPEAT buttons become lit), to repeat the rehearsal operation until you press the STOP (8) button. 58 TASCAM DP-24

Section	Page
1 – Introduction	8
Features	8
Items included with the product	8
Conventions used in this manual	8
Intellectual property rights	9
Precautions for placement and use	9
Beware of condensation	9
Cleaning the unit	9
About SD cards	9
Precautions for use	10
About CDs (Compact Discs)	10
Precautions for use	10
About CD-R and CD-RW discs	10
2 - Quick Guide	12
Playback and mixing	12
Preparation	12
Listening to the demo song	13
Recording and mastering	14
Creating a new song	14
Connecting and setting the input sources	15
Setting the guitar as the recording source for TRACK 1	15
Adjusting and monitoring the input level	15
Recording a guitar to TRACK 1	16
Playing back the recording	16
Recording a guitar to TRACK 2	16
Recording a vocal to TRACK 3	17
Mixing the tracks	18
Mastering a recording	19
Creating an audio CD with the master file	21
Inserting a CD	21
Writing to a CD-R/CD-RW	22
Ejecting a CD	23
Shutting down	23
3 – Names and Functions of Parts	24
Top panel	24
Front panel	28
Rear panel	29
Home screen	30
Menu structure	31
Screen operations	32
4 – Preparation	34
Inserting and removing SD cards	34
Inserting an SD card	34
Removing the card	34
About write-protected SD cards	34
Powering the unit	34
Start-up & Shutdown	35
Starting up the unit	35
Shutting down	35
Setting the date and time	35
Preparing an SD card for use	36
Recorder modes	36
Connecting other equipment	36
Front panel	36
Rear panel	37
Adjusting the contrast	37
5 - Song Management	38
Editing names	38
Loading a song	38
Creating a new song	38
Saving a song	39
Viewing song information	40
Copying songs	40
Erasing songs	41
Protecting songs	41
Deleting unnecessary audio data from a song	42
Changing a song name	43
6 - Basic Recording	44
Selecting the input sources	44
Assigning inputs	44
Assigning to a mono track	44
Assigning to a stereo track	44
Assigning to a stereo bus	44
Checking the assignment	45
Canceling an assignment	45
Using phantom power	45
Monitoring	45
Monitor selection	45
OL indicators and level meters	46
Setting the Mixer screen	46
Using EQ (equalizer)	46
DIGITAL TRIM setting (Track only)	47
Built-in Send Effects and External Effects	47
Setting built-in effects	47
Setting the stereo position	48
Changing the signal phase	48
Checking the fader level	48
Solo	48
Muting tracks	48
Rehearsing the recording	49
Making the first recording	49
Multitrack recording	50
Setting the tracks for recording	50
Setting track pan and level	50
Input selection and assignment	50
Setting input levels	50
Recording	50
Undoing an operation	50
Setting the undoing feature	50
Undoing the last operation (single undo)	51
Undoing previous operations (multi-undo)	51
7 - Recorder Functions	52
Punching in and out	52
Using a foot switch to punch in/out	52
Setting the foot switch	52
Bouncing tracks	53
Performing the track bouncing	53
Checking the result	53
Direct Location Function	54
Locating directly a specified time	54
Locating directly a specified measure/beat	54
Location marks	54
Setting a location mark	54
Skipping to location marks	55
Deleting a location mark	55
Returning to zero (TO ZERO) and returning to last recording position (TO LAST REC)	55
Fast forward/rewind search	55
Jog positioning	55
Viewing the track's waveform	55
Listening to the track sounds	55
Repeat playback	56
Setting IN/OUT points	56
Using repeat playback	56
Moving back a few seconds for replay (jump back playback)	56
Checking cueing points (preview)	57
Auto punch in/out	57
Setting punch in/out points	58
Checking punch in/out points	58
Rehearsing punch in/out	58
Performing auto punch in/out	59
Checking a take	59
Virtual tracks	59
8 - Track Editing	60
Overview of track editing	60
Editing points	60
Basic editing procedures	60
Explanation of items	60
COPY/PASTE	61
COPY/INSERT	61
MOVE/PASTE	62
MOVE/INSERT	62
OPEN (Insert Silence)	62
CUT (Remove Part)	62
SILENCE (Erase Part)	63
CLONE TRACK (Track Duplication)	63
CLEAN OUT (Delete Track)	63
9 - Using Built-In Effects	64
Dynamic effects	64
Inserting a dynamic effect	64
Editing a dynamic effect	64
Guitar effects	64
Inserting a guitar effect	64
Editing guitar effects	65
Calling effects from the guitar effect library	65
Saving guitar effects in the library	65
Send effects	65
Using send effects	65
Editing send effects	65
Calling the send effect library	66
Saving send effects in the library	66
10 - Mixing Down and Mastering Tracks	68
Mixing down tracks	68
Levels and balance	68
Fader group	68
Stereo position (panning)	68
TRACK EQ (equalizer)	68
Send effects	69
Creating a master file	69
Setting the start and end points	69
Creating a master file	70
Exiting Mixdown mode	70
Checking the master file	70
Ending master file checking	71
Finishing up a master file (mastering)	71
Mastering procedures	71
Using the mastering EQ (equalizer)	71
Using mastering compression	72
Using normalize	73
Using the noise shaper (Noise Shaped Dithering)	73
Exiting Mastering mode	73
11 - Various Other Functions	74
Metronome	74
MIDI Sync	74
MIDI remote control	75
Tuner function	75
Setup (PREFERENCE)	76
Auto Monitor	76
Restoring the initial preference settings	77
Viewing information	77
12 - SD Card Management	78
Quick formatting an SD card	78
Full formatting an SD card	79
13 - Exchanging Data with a Computer	80
Operating system requirements	80
Connecting to a computer	80
Disconnecting	81
Track import and export	82
Importing tracks	82
Exporting tracks	83
Deleting files from the AudioDepot folder	83
14 - Using CDs	84
Using the CD drive	84
Preparations before using CDs with this unit	84
Types of CDs that can be used with this unit	84
Loading and ejecting CDs	85
Loading a CD	85
Ejecting a CD	86
Forcing disc ejection	86
Playing back an Audio CD	86
Creating an Audio CD	87
Using Disc At Once	87
Using Track At Once	88
Using LIVE WRITER	89
Finalizing a CD	90
Importing songs from an Audio CD	90
Erasing a CD-RW	91
Media Compatibility Table	91
15 – Troubleshooting	92
16 – Messages	93
General messages	93
CD mode messages	95
CD-related error messages	96
17 – Specifications	97
Ratings	97
Input/output ratings	97
Analog audio input/output ratings	97
Control input/output ratings	97
Audio performance	97
Operating requirements	97
Dimensional drawings	98
General	98
Block diagram	99
Level diagram	100
18 – Appendix	101
MIDI Control Change message	101
Mixer control change parameters	101
MIDI Program Change message	102
Dynamic effects	102
Preset libraries of the send effects	102
Preset libraries of the guitar effects	102
MIDI Implementation Chart	103

Match case Limit results 1 per page

TASCAM DP-24

7 - Recorder Functions

Setting punch in/out points

There are two methods to set the punch in/out points.

LAST REC:

This option sets the start and end points of the last

recording (or recording rehearsal) as the punch in/out

points.

The display returns to the Home screen, and

Auto

Punch

appears on the top of the screen.

IN - OUT:

This option sets the IN point and the OUT point as

the punch in/out points. The first of these points will

be used as the punch in point, and the second as the

punch out point.

The display returns to the Home screen, and

Auto

Punch

appears on the top of the screen.

When the recorder is stopped, press the HOME

button to open the Home screen.

Press the REC button for the track that you want to

punch in/out automatically.

Press the AUTO PUNCH button to open the

AUTO

PUNCH

screen.

NOTE

If you press the

AUTO PUNCH

button without any tracks

in recording standby, even after that you can press the

REC

button of any track to put it into recording standby.

4. Use the CURSOR (

) buttons to select (blue

highlight)

MODE

PREROLL

POSTROLL

, and

then use the JOG/DATA dial to select the value.

MODE

LAST REC

IN-OUT

PREROLL

1.0

9.9 sec

POSTROLL

1.0

9.9 sec

After setting

MODE

PREROLL

, and

POSTROLL

press the

(

)

button.

You can press the

AUTO PUNCH

button to return to

the Home screen without entering Auto Punch In/Out

mode.

Checking punch in/out points

When punch in/out points are set, you can confirm the

setting by pressing the

PLAY (

)

button.

The playback starts from the pre-roll point to the post-roll

point.

If you want to change the punch in/out points, locate the

desired points and set the punch in/out points again.

If there are no problems about punch in/out points, pre-

roll time, and post-roll time perform the rehearsal, as

described below.

Rehearsing punch in/out

You can rehearse before performing punch in/out. In the

rehearsal, the monitor operates the same way as for the

actual recording, but the recording is not performed.

When the AUTO PUNCH button is lit and one of the

tracks is in recording standby, press the REHEARSE

button.

The

REHEARSE

button becomes lit.

2. Press the RECORD (

) button.

Auto punch in/out rehearsal starts.

Playback starts from the pre-roll point. You can

•

monitor both the track playback signal and the

input source signal.

When the punch in point is reached, the monitoring

•

changes to input source signal only, and the

RECORD (

)

button starts flashing (to indicate this

is a rehearsal).

When the punch out point is reached, the

•

monitoring of both the track playback signal and

input source signal starts, and the

RECORD (

)

button becomes unlit.

Playback continues until the post-roll point and

•

stops.

Before starting your rehearsal, you can press the

REPEAT

button (so that all three

AUTO PUNCH

REHEARSE

, and

REPEAT

buttons become lit), to

repeat the rehearsal operation until you press the

STOP (

)

button.