TEAC NT-505 Owners Manual English Francais Espanol - Page 17

Basic operation, Operate the playback device.

Get TEAC NT-505 PDF manuals and user guides View all TEAC NT-505 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Basic operation 1 Shift the POWER switch to its ON position to turn the unit on. oo If a stereo amplifier is connected to this unit, always turn its power ON very last. 2 Turn the SOURCE knob to select the input source. 3 Operate the playback device. Refer to the operation manual of that device. EN 4 Adjust the volume. When using the line outputs When LINE OUT LEVEL is set to VARIABLE, turn this unit's VOLUME knob to adjust the volume. When LINE OUT LEVEL is set to any other setting, the volume cannot be adjusted from this unit. Use the stereo amplifier or other device connected to this unit to adjust the volume. When headphones are connected to this unit Turn this unit's VOLUME knob to adjust the volume. oo When this unit's VOLUME knob is enabled, the volume setting will be shown. The selected source appears on the display. oo You can also use the input selection buttons on the remote control. oo If the input signal is not a digital audio signal or is an audio signal format that is not supported by this unit, such as Dolby Digital or DTS, no audio will be output. Set the digital output of the connected device to PCM audio output. oo To play back audio files when this unit is set to USB, you must first install a dedicated driver on the computer before connecting them (page 25). oo DSD data can only be played back when the input source is USB or NET (including USB flash drives) or when using DoP format digital input. oo To use NET or the front USB port, install the TEAC HR Streamer (free) on a smartphone or tablet, and connect it to the same network as the unit. 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
EN
17
Basic operation
1
Shift the POWER switch to its ON position to
turn the unit on.
o
If a stereo amplifier is connected to this unit, always turn its
power ON very last.
2
Turn the SOURCE knob to select the input
source.
The selected source appears on the display.
o
You can also use the input selection buttons on the remote
control.
o
If the input signal is not a digital audio signal or is an audio
signal format that is not supported by this unit, such as
Dolby Digital or DTS, no audio will be output. Set the digital
output of the connected device to PCM audio output.
o
To play back audio files when this unit is set to USB, you
must first install a dedicated driver on the computer before
connecting them (page 25).
o
DSD data can only be played back when the input source is
USB or NET (including USB flash drives) or when using DoP
format digital input.
o
To use NET or the front USB port, install the TEAC HR Streamer
(free) on a smartphone or tablet, and connect it to the same
network as the unit.
3
Operate the playback device.
Refer to the operation manual of that device.
4
Adjust the volume.
When using the line outputs
When LINE OUT LEVEL is set to VARIABLE, turn this unit’s VOLUME
knob to adjust the volume.
When LINE OUT LEVEL is set to any other setting, the volume
cannot be adjusted from this unit. Use the stereo amplifier or
other device connected to this unit to adjust the volume.
When headphones are connected to this unit
Turn this unit’s VOLUME knob to adjust the volume.
o
When this unit’s VOLUME knob is enabled, the volume set-
ting will be shown.