Toshiba DKT3010-SD User Guide - Page 107

IP Telephone Start Up Sequence - manuals

Get Toshiba DKT3010-SD - Digital Phone PDF manuals and user guides View all Toshiba DKT3010-SD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 107 highlights

IPT1020-SD Settings IPT-to-IP Network Connection Instructions 6. If the IPT is connected to a router or other gateway device, press )%. Enter the router address, then press +ROG. Only used if Step 3, above, is set for manual setting. 7. Press )%. Enter a Station ID for the IPT and press +ROG. This is usually your telephone's primary number (PDN). 8. Press )% to enter the CTX Strata Net node number of the CTX node that contains the BIPU-M1A to which this IPT interfaces, then press +ROG. This FB setting is for CTX networked systems only. 9. Press )% for BIPU IP address mode. Press one of the following: : manual setting, then press +ROG. Press )% and enter the BIPU IP address, then press +ROG. (e.g., if the BIPU IP address is "192.168.1.241," enter it in this format : auto setting by broadcast, then press +ROG. : auto setting by multicast (IPT doesn't support multicast setting in this first release), then press +ROG. 10. Press +ROG again to set all the above data. 11. Go off-hook and hang up. The IPT will search for the BIPU-M1A, initialize and then set the IP address (from 20 sec. to 60 sec.). Time, Date and PDN displays on LCD when the information is set. Note See "IP Telephone Start Up Sequence" below for an explanation of the LCDs that you will see during this procedure. IP Telephone Start Up Sequence After the IP telephone network setting has been programmed, the following displays occur after the IP telephone is hung-up: Action 1. IPT initializes. LCD Indication INITIALIZING PLEASE WAIT... Remarks Strata CTX DKT/IPT Telephone 06/03 93

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
IPT1020-SD Settings
IPT-to-IP Network Connection Instructions
Strata CTX DKT/IPT Telephone
06/03
93
6.
If the IPT is connected to a router or other gateway device, press
)%¶
. Enter the
router address, then press
+ROG
. Only used if Step 3, above, is set for manual
setting.
7. Press
)%³
. Enter a Station ID for the IPT and press
+ROG
. This is usually your
telephone
’
s primary number (PDN).
8. Press
)%¹
to enter the CTX Strata Net node number of the CTX node that contains
the BIPU-M1A to which this IPT interfaces, then press
+ROG
. This FB setting is
for CTX networked systems only.
9. Press
)%µµ
for BIPU IP address mode. Press one of the following:
µ
: manual setting, then press
+ROG
. Press
)%µ»
and enter the BIPU IP address,
then press
+ROG
. (e.g., if the BIPU IP address is
“
192.168.1.241,
”
enter it in this
format
µ´»
¾
µ¹½
¾
µ
¾
»¶µ
).
»
: auto setting by broadcast, then press
+ROG
.
¼
: auto setting by multicast (IPT doesn
’
t support multicast setting in this first
release), then press
+ROG
.
10. Press
+ROG
again to set all the above data.
11. Go off-hook and hang up. The IPT will search for the BIPU-M1A, initialize and
then set the IP address (from 20 sec. to 60 sec.). Time, Date and PDN displays on
LCD when the information is set.
Note
See
“
IP Telephone Start Up Sequence
”
below for an explanation of the LCDs
that you will see during this procedure.
IP Telephone Start Up Sequence
After the IP telephone network setting has been programmed, the following displays
occur after the IP telephone is hung-up:
Action
LCD Indication
Remarks
1.
IPT
initializes.
INITIALIZING
PLEASE WAIT...