ViewSonic LS550WH - 3000 LED Lumens WXGA Short Throw LED Projector w/ 125% Rec. - Page 35

Projector IP Address, Enter, LAN Settings, Static IP, DNS Server

Get ViewSonic LS550WH - 3000 LED Lumens WXGA Short Throw LED Projector w/ 125% Rec. 709 PDF manuals and user guides View all ViewSonic LS550WH - 3000 LED Lumens WXGA Short Throw LED Projector w/ 125% Rec. 709 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

• If the RJ45 cables are not properly connected, the Projector IP Address, Subnet Mask, Default Gateway and DNS Server settings will display 0.0.0.0. Make sure the cables are properly connected and perform the procedures above again. • If you need to connect to the projector in its standby mode, set Standby LAN Control to On in the ADVANCED > LAN Control Settings menu. • If you are in a non-DHCP environment: 1. Repeat steps 1-2 above. 2. Highlight LAN Settings and press / to select Static IP. 3. Contact your ITS administrator for information on the Projector IP Address, Subnet Mask, Default Gateway, DNS Server settings. 4. Press to select the item you want to modify and press Enter. 5. Press / to move the cursor and the press / to enter the value. 6. To save the settings, press Enter. If you do not want to save the settings, press Exit. 7. Press to highlight Apply and press Enter. NOTE: • If the RJ45 cables are not properly connected, the Projector IP Address, Subnet Mask, Default Gateway, DNS Server settings will display 0.0.0.0. Make sure the cables are properly connected and perform the procedures above again. • If you wish to connect to the projector in its standby mode, be sure you have selected Static IP and obtained the Projector IP Address, Subnet Mask, Default Gateway and DNS Server information when the projector is on. 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
35
• If the RJ45 cables are not properly connected, the
Projector IP Address
,
Subnet Mask
,
Default Gateway
and
DNS Server
se´ngs will display 0.0.0.0. Make
sure the cables are properly connected and perform the procedures above again.
• If you need to connect to the projector in its standby mode, set
Standby LAN Control
to
On
in the
ADVANCED
>
LAN Control Settings
menu.
•
If you are in a non-DHCP environment:
1.
Repeat steps 1-2 above.
2.
Highlight
LAN Settings
and press
/
to select
Static IP
.
3.
Contact your ITS administrator for informa°on on the
Projector IP Address
,
Subnet Mask
,
Default Gateway
,
DNS Server
se´ngs.
4.
Press to select the item you want to modify and press
Enter
.
5.
Press
/
to move the cursor and the press
/
to enter the value.
6.
To save the se´ngs, press
Enter
. If you do not want to save the se´ngs, press
Exit
.
7.
Press
to highlight
Apply
and press
Enter
.
NOTE:
• If the RJ45 cables are not properly connected, the
Projector IP Address
,
Subnet Mask
,
Default Gateway
,
DNS Server
se´ngs will display 0.0.0.0. Make
sure the cables are properly connected and perform the procedures above again.
• If you wish to connect to the projector in its standby mode, be sure you
have selected
Static IP
and obtained the
Projector IP Address
,
Subnet Mask
,
Default Gateway
and
DNS Server
informa°on when the projector is on.