ViewSonic PJ501 User Guide - Page 12

Operations - replacement lamp

Page 12 highlights

Operations Power ON NOTE: Refer to "Example of System Setup" on page 8. 1 Make sure the power cord is connected correctly and lens cap has been removed. Set the Power Switch to [I] ON. The unit is now in Standby mode and the POWER indicator LED turns a steady orange. 2 Press the STANDBY/ON button on the control panel or the remote control. Warm-up begins and the power indicator blinks in green. 3 After several seconds the lamp will stop blinking and will turn to continuous green, indicating that the projector is ready to use. 4 Adjust the size of the projected image with the Zoom knob. 5 Adjust focus using the Focus ring. Power OFF NOTE: See Caution below. 1 Press the STANDBY/ON button on the control panel or the remote control. The message "POWER OFF?" will display on the screen, and the message will disappear in 5 seconds. During this message indication, press the STANDBY/ON button again. The projector lamp shuts off and lamp cooling begins. 2 Wait for the cooling fan to stop. The POWER indicator blinks orange during lamp cooling. Pressing the STANDBY/ON button has no effect while the POWER indicator is blinking. 3 The system assumes the Standby mode when cooling is complete. The POWER indicator ceases blinking and changes to a steady orange. Check that the indicator is orange and set the POWER switch to [O]. The POWER indicator turns off when the Power Switch is set to [O] OFF. Remember to replace the lens cap after use. Power Indicator Standby/On Button Zoom Knob Focus Ring Remote Control Power Switch Figure 9: Power Buttons NOTE: Except in emergencies, do not turn off the Power Switch unless the POWER indicator is a steady orange. Otherwise improper cooling of the lamp will reduce the life of the lamp or may damage the lamp. CAUTION • To turn OFF the projector press the Standby/ON button and hold for 2 seconds . • The POWER LED on the control pad flashes orange during cool-down. • Wait until the POWER LED changes to a steady orange before you set the Power Switch to [O] OFF. 9 ViewSonic PJ500/PJ550/PJ501/PJ551

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32

9
ViewSonic
PJ500/PJ550/PJ501/PJ551
Operations
Power ON
NOTE:
Refer to “Example of System Setup” on page 8.
1
Make sure the power cord is connected correctly and lens cap has been removed. Set the Power
Switch to [I] ON. The unit is now in Standby mode and the POWER indicator LED turns
a
steady orange.
2
Press the STANDBY/ON button on the control panel or the remote control. Warm-up begins and
the power indicator blinks in green.
3
After several seconds the lamp will stop blinking and will turn to continuous green, indicating
that the projector is ready to use.
4
Adjust the size of the projected image with the Zoom knob.
5
Adjust focus using the Focus ring.
Power OFF
NOTE:
See Caution below.
1
Press the STANDBY/ON button on the control panel or the remote control. The message
“POWER OFF?” will display on the screen, and the message will disappear in 5 seconds. During
this message indication, press the STANDBY/ON button again. The projector lamp shuts off and
lamp cooling begins.
2
Wait for the cooling fan to stop. The POWER indicator blinks orange during lamp cooling.
Pressing the STANDBY/ON button has no effect while the POWER indicator is blinking.
3
The system assumes the Standby mode when cooling is complete. The POWER indicator ceases
blinking and changes to a steady orange. Check that the indicator is orange and set the POWER
switch to [O]. The POWER indicator turns off when the Power Switch is set to [O] OFF.
Remember to replace the lens cap after use.
NOTE:
Except in emergencies, do not turn off the Power Switch unless the POWER indicator is
a
steady orange. Otherwise improper cooling of the lamp will reduce the life of the lamp or may
damage the lamp.
Figure 9: Power Buttons
CAUTION
To turn OFF the projector press the Standby/ON button and hold for 2 seconds .
The POWER LED on the control pad flashes orange during cool-down.
Wait until the POWER LED changes to a steady orange before you set the Power Switch to [O] OFF.
Power Indicator
Standby/On Button
Zoom Knob
Focus Ring
Power Switch
Remote Control