ViewSonic PJ658 PJ658 User Guide - Page 21

Power on/off

Get ViewSonic PJ658 - XGA LCD Projector PDF manuals and user guides
UPC - 766907222210
View all ViewSonic PJ658 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Power on/off Power on/off WARNING ►When the power is on, a strong light is emitted. Do not look into the lens of projector. Also do not peep at the inside of projector through a hole. NOTE • Turn the power on/off in right order. Please power on the projector prior to the connected devices. Power off the projector later than the connected devices. Turning on the power 1. Make sure that the power cord is firmly and correctly connected to the projector and the outlet. STANDBY/ON button 2. Remove the lens cover, and set the power switch to the ON position. The power indicator will light up in steady orange. Then VIDEO RGB SEARCH ASPECT AUTO BLANK MAGNIFY ON HOME PAGE UP VOLUME OFF END PAGE DOWN MUTE FREEZE MY BUTTON KEYSTONE 1 2 wait several seconds because the buttons may not func- POSITION MENU ENTER tion for these several seconds. ESC RESET POWER indicator (1) When AUTO ON in the OPTION menu is set to TURN ON: The lamp will only be automatically turned on when the Power switch is turned on after the power was turned off by Power switch last time. Afterwards the POWER indicator will begin blinking in green. When the power is completely on, the indicator will stop blinking and light in green. (2) When AUTO ON in the OPTION menu is set to TURN OFF please see step 3. 3. Press the STANDBY/ON button on the projector or the remote control. To display the picture, select an input signal according to the section "Selecting an input signal". POWER (Steady orange) POWER (Blinking in green) POWER (Steady green) Turning off the power Please pay special attention to below two points when you do: (1) Please do not turn the projector on again for at least 10 minute in this case. Neglect could shorten the lifetime of the lamp. (2) During use or immediately after use, do not touch around the lamp and vents of the projector It could cause a burn. 1. Press the STANDBY/ON button on the projector or the remote control. The message "Power off?" will appear on the screen for about 5 seconds. Power off? 2. Press the STANDBY/ON button on the projector or the remote control again while the message appears. The projector lamp will go off, and the POWER indicator will begin blinking in orange. POWER (Blinking in orange) Then the POWER indicator will stop blinking and light in steady orange when the lamp cooling is complete. 3. Make sure that the power indicator lights in steady orange, and set the power switch to the OFF position. The POWER indicator will go off. Attach the lens cover. POWER (Steady orange) ViewSonic PJ658 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
Power on/off
Power on/off
WARNING
►
When the power is on, a strong light is emitted. Do not look into
the lens of projector. Also do not peep at the inside of projector through a hole.
NOTE
•
Turn the power on/off in right order. Please power on the projector prior
to the connected devices. Power off the projector later than the connected devices.
Turning on the power
1.
Make sure that the power cord is firmly and cor-
rectly connected to the projector and the outlet.
2.
Remove the lens cover, and set the power switch to
the ON position.
The power indicator will light up in steady orange. Then
wait several seconds because the buttons may not func-
tion for these several seconds.
(1)
When AUTO ON in the OPTION menu is set to TURN ON:
The lamp will only be automatically turned on when the
Power switch is turned on after the power was turned off by
Power switch last time. Afterwards the POWER indicator
will begin blinking in green. When the power is completely
on, the indicator will stop blinking and light in green.
(2)
When AUTO ON in the OPTION menu is set to TURN OFF
please see step 3.
3.
Press the STANDBY/ON button on the projector or the re-
mote control.
To display the picture, select an input signal according to the sec-
tion "Selecting an input signal".
Turning off the power
Please pay special attention to below two points when you do:
(1) Please do not turn the projector on again for at least 10 minute in this case. Neglect
could shorten the lifetime of the lamp.
(2) During use or immediately after use, do not touch around the lamp and vents of the
projector It could cause a burn.
1.
Press the STANDBY/ON button on the projector or the remote control.
The message "Power off?" will appear on the screen for about 5
seconds.
2.
Press the STANDBY/ON button on the projector or the remote
control again while the message appears.
The projector lamp will go off, and the POWER indicator will begin
blinking in orange.
Then the POWER indicator will stop blinking and light in steady
orange when the lamp cooling is complete.
3.
Make sure that the power indicator lights in steady orange, and
set the power switch to the OFF position. The POWER indicator will
go off. Attach the lens cover.
POWER
(Steady orange)
POWER
(Blinking in green)
POWER
(Steady green)
STANDBY/ON
button
POWER
indicator
Power off?
POWER
(Blinking in orange)
POWER
(Steady orange)
17
ViewSonic
PJ658