ViewSonic PJD5351 PJD5152, PJD5352 User Guide (English)
ViewSonic PJD5351 - DLP Projector Manual
 |
UPC - 766907341010
View all ViewSonic PJD5351 manuals
Add to My Manuals
Save this manual to your list of manuals |
ViewSonic PJD5351 manual content summary:
- ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 1
ViewSonic® PJD5152 / PJD5352 DLP Projector IMPORTANT: Please read this User Guide to obtain important information on installing and using your product in a safe manner, as well as registering your product for future service. Warranty information contained in this User Guide will describe your - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 2
and used in accordance with the instructions, may cause harmful interference to radio by turning the equipment off and on, the user is encouraged to try to correct the interference by classe B est conforme à la norme NMB-003 du Canada. CE Conformity for European Countries The device complies with the - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 3
of the RoHS Directives as noted below: Examples of exempted components are: 1. Mercury in compact fluorescent lamps not exceeding 5 mg per lamp and in other lamps not specifically mentioned in the Annex of RoHS Directive. 2. Lead in glass of cathode ray tubes, electronic components, fluorescent - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 4
interest of continuing product improvement, ViewSonic Corporation reserves the right to change product specifications without notice. Information in this For Your Records PJD5152 / PJD5352 ViewSonic DLP Projector VS13307 / VS13147 PJD5152_PJD5352_UG_ENG Rev. 1B 03-05-10 The lamp in this product - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 5
instructions 3 Introduction 5 Projector features 5 Shipping contents 6 Projector exterior view 7 Controls and functions 8 Positioning your projector the projector 43 Lamp information 44 Troubleshooting 50 Specifications 51 Projector specifications 51 Dimensions 52 Ceiling mount - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 6
the product. Safety Instructions 1. Please read this manual before you operate your projector. Save it for future reference. 2. Do not look straight at the projector lens during operation. The intense light beam may damage your eyes. 3. Refer servicing to qualified service personnel. 4. Always open - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 7
transporting or installation. It should be used with a commercially available theft prevention cable. Safety instructions for ceiling mounting of the projector We want you to have a pleasant experience using your projector, so we need to bring this safety matter to your attention to prevent damage - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 8
a user-friendly design to deliver high reliability and ease of use. The projector offers • Component HDTV compatibility (YPbPr) • High quality manual zoom lens • The apparent brightness of the projected lamp brightness will decline over time and may vary within the lamp manufacturers specifications. - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 9
may differ from those illustrated. Projector Power Cord VGA Cable Multi-language user manual DVD Quick Start Guide Remote Control & Battery Pull the tab before using the remote control. Soft carry case (for the PJD5352) Optional accessories 1. Ceiling mount 2. Replacement lamp 6 Introduction - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 10
Projector exterior view Front/upper side 1 2 3 4 Rear/lower side 8 9 10 11 18 1. External control panel (See "Projector and remote control" on page 8 for details.) 2. Vent (heated air exhaust) 3. Quick-release button 4. Lens cover 5. Focus ring and Zoom ring 6. Front IR remote Lamp - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 11
the image size and clarity" on page Down) 26 for details. 3. TEMPerature indicator light Manually corrects distorted images resulting from an angled projection. See Lights up red if the projector's temperature "Correcting keystone" on page 26 for becomes too high. See "Indicators" on page - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 12
the lamp has developed a (OSD) menu item. problem. See "Indicators" on page 49 for 18. Keystone keys ( / ) details. Manually corrects 23. See "Selecting a picture mode" on page 29 for details. Toggles the projector audio between on Enacts the selected On-Screen Display and off. (OSD) menu - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 13
remote control and the IR sensor on the projector that might obstruct the infra-red beam. Replacing the remote control battery 1. Pull out the battery holder. Please follow the illustrated instructions battery according to the battery manufacturer's instructions. • Never throw a battery into a fire. - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 14
for quick setup and portability. 2. Front Ceiling Select this location with the projector suspended upside-down from the ceiling in front of the screen. Purchase the projector ceiling mount kit from your dealer to mount your projector on the ceiling. Set Front Ceiling in the SYSTEM SETUP: Basic - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 15
physically test the projection size and distance using the actual projector in situ before you permanently install it, so as to make allowance for this projector's optical characteristics. This will help you determine the exact mounting position so that it best suits your installation location. 12 - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 16
connect one end of the cable to the audio output socket of the device, and the other end to the AUDIO IN socket of the projector. 4. If you wish, you can use another suitable audio cable and connect one end of the cable to the AUDIO OUT socket of the - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 17
a monitor If you want to view your presentation close-up on a monitor as well as on the screen, you can connect the COMPUTER OUT signal output socket on the projector to an external monitor with a VGA cable following the instructions below: To connect the projector to a monitor: 1. Connect the - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 18
source device, you should elect to use the S-Video option. See "Connecting an S-Video source device" on page 17 for how to connect the projector to an S-Video device. Least video quality Composite Video is an analog video and will result in a perfectly acceptable, but less than optimal result from - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 19
To connect the projector to a Component Video projector. 3. If you wish to make use of the projector projector. 4. projector, and the other end to your external speakers Once connected, the audio can be controlled by the projector cable • The projector is only capable after the projector is turned - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 20
can continue with this procedure. • If not, you will need to reassess which method you can use to connect to the device. To connect the projector to an S-Video source device: 1. Take an S-Video cable and connect one end to the S-Video output socket of the Video source device. 2. Connect the - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 21
can continue with this procedure. • If not, you will need to reassess which method you can use to connect to the device. To connect the projector to a composite Video source device: 1. Take a Video cable and connect one end to the composite Video output socket of the Video source device. 2. Connect - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 22
If it is closed, it could become deformed due to the heat produced by the projection lamp. 3. Press II POWER on the projector or remote control to start the projector. The POWER indicator light stays blue when the projector is on. The start up procedure takes about 30 seconds. In the later stage of - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 23
a valid signal, the message 'No Signal' will continue to be displayed until an input signal is found. You can also press SOURCE on the projector or remote control to select your desired input signal. See "Switching input signal" on page 24 for details. If the frequency/resolution of the input signal - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 24
3D Sync 3D Sync Invert Color Management Analog RGB Off Auto 16 0 On Disable MENU Exit 2. Use / to highlight the SYSTEM SETUP: Basic menu. Language Projector Disable Off Disable ViewSonic On Analog RGB MENU Exit 4. Press MENU/EXIT twice* on the projector or Exit on the remote control to leave - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 25
projector . Press MODE/ENTER on the projector or Enter on the remote control. The Security Settings page user manual in a safe place. 5. To leave the OSD menu, press MENU/EXIT on the projector or Exit on the remote not record the password in this user manual, and you absolutely do not remember - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 26
off your projector. 3. Seek help from the local service center to decode the number. You may be required to provide proof of purchase documentation to verify that you are an authorized user of the projector. RECALL PASSWORD Please write down the recall code, and contact ViewSonic Customer Center - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 27
Search function in the SOURCE menu is On if you want the projector to automatically search for the signals. You can also manually cycle through the available input signals. 1. Press SOURCE on the projector or remote control. A source selection bar is displayed. 2. Press / until your desired signal - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 28
the lamp may cause damage to your eyes. • Be careful when you press the adjuster button as it is close to the exhaust vent where hot air comes from. Auto-adjusting the image In some cases, you may need to optimize the picture quality. To do this, press AUTO on the projector or remote - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 29
to the screen. To correct this, besides adjusting the height of the projector, you will need to manually correct it following one of these steps. • Using the remote control Press / on the projector or remote control to display the Keystone correction page. Press to correct keystoning at the - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 30
center of the picture. Press the key repeatedly until the picture size is suitable for your need. 3. Use the directional arrows ( , , , ) on the projector or remote control to navigate the picture. 4. To restore the picture to its original size, press AUTO. You can also press Magnify -. When the key - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 31
and the white portions are active areas. OSD menus can be displayed on those unused black areas. 1. Auto: Scales an image proportionally to fit the projector's native resolution in its horizontal width. This is suitable for the incoming image which is neither in 4:3 nor 16:9 and you want to 16:10 - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 32
one of the following steps. • Press MODE/ENTER on the projector or Color Mode on the remote control repeatedly until your desired mode is selected. • Go to the DVs through the PC input for best viewing in a blackened (little light) environment. 5. User 1/User 2 mode: Recalls the settings customized - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 33
can use one of the picture modes (except the User 1/User 2) as a starting point and customize the settings. 1. Press MENU/EXIT on the projector or MENU on the remote control to open the OnScreen Display (OSD) menu. to suit your selected input and viewing environment. -30 0 +30 30 Operation - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 34
in the projected picture. It enables a greater than 50% brightness increase in mid-tone images, which are common in video and natural scenes, so the projector reproduces images in realistic and true colors. If you prefer images with that quality, select On. If you don't need it, select Off. When Off - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 35
to make adjustments. To adjust the settings: 1. Go to the DISPLAY menu and highlight Color Management. 2. Press MODE/ENTER on the projector or Enter on the remote control and the Color Management page is displayed. 3. Highlight Primary Color and press / to select a color from among Red, Yellow - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 36
image In order to draw the audience's full attention to the presenter, you can use on the projector or Blank on the remote control to hide the screen image. Press any key on the projector or remote control to restore the image. The word 'BLANK' appears at the lower right corner of the screen - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 37
of the screen. To release the function, press any key on the projector or remote control. Even if an image is frozen on the screen, the projector from over-heating. In cases like this, you should switch to High Altitude Mode to solve these symptoms. However, this is not to state that this projector - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 38
continue to run for approximately 90 seconds to cool down the projector. 3. Disconnect the power cord from the wall socket if the projector will not be used in an extended period of time. CAUTION • To protect the lamp, the projector will not respond to any commands during the cooling process. • To - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 39
Phase H. Size Zoom 3D Sync TI 3D DLP Link/Off 3D Sync Invert Disable/Invert Primary Color R/G/B/C/M/Y Color Hue Management Saturation Gain PC source: Brightest/Daylight/ViewMatch/ Color Mode Cinema/User 1/User 2 Video source: Brightest/Gaming/ViewMatch/ Cinema/User 1/User 2 PC source - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 40
SETUP: Basic Projector Position Auto hr/2 hr/3 hr/4 hr/8 hr/12 hr Splash Screen Black/Blue/ViewSonic Message On/Off Quick Cooling On/Off High Altitude Mode On/Off DCR CC1/CC2/CC3/CC4 Lamp Mode Normal/Economic Lamp Settings Reset Lamp Timer Equivalent Lamp Hour Security Settings Change - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 41
wear a pair of 3D glasses to view the 3D images. • TI 3D DLP Link: Enable projector for TI 3D DLP Link. • Off: Disable 3D. 3D Sync Invert When the 3D Sync function is on enable this function to correct the problem. (For TI 3D DLP Link only) Color Management See "Color Management" on page 32 - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 42
Mode Pre-defined picture modes are provided so you can optimize your projector image set-up to suit your program type. See "Selecting image based on the selections listed on the same page below. See "Setting the User 1/User 2 mode" on page 30 for details. Brightness Adjusts the brightness of the - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 43
panel key functions except II POWER on the projector and keys on the remote control. See "Locking control keys" on be displayed during projector start-up. Three options are available: ViewSonic logo, Black the function and the projector will automatically switch the lamp mode between normal and - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 44
made as below will have an effect on the projector speaker. Be sure you have made a correct connection to the projector audio input. See "Connection" on page 13 NTSC. Caption Version Selects a preferred closed captioning mode. To view captions, select CC1, CC2, CC3, or CC4 (CC1 displays captions in - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 45
the total lamp hour is calculated. See "Utilizing the password function" on page 22 for details, Reset All Settings Current System Status Returns all settings to the factory preset values. The following settings will still remain: Phase, H. Size, User 1, User 2, Language, Projector Position, High - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 46
the projector except the lamp. case. Storing the projector If you need to store the projector for an extended time, please follow the instructions below: • Make sure the temperature and humidity of the storage area are within the recommended range for the projector. Please refer to "Specifications - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 47
menu. 4. To leave the menu, press MENU/EXIT on the projector or Exit on the remote control. You can also get the lamp hour information on the INFORMATION menu. Extending lamp life The projection lamp is a consumable item. To keep the lamp life as long as possible, you can do the following settings - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 48
, it must be replaced after 4000 hours usage. The lamp MUST be replaced before the projector will operate normally. Notice Replace Lamp Now Lamp > 4000 Hours Lamp usage time exceeded OK Notice Lamp usage time exceeded Replace lamp (refer to User Manual) Then reset lamp timer OK Maintenance 45 - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 49
of sharp edges in the lamp compartment. Wash hands after lamp replacement. • Only ViewSonic certified lamps are tested with this projector. Use of other lamps may cause electrical shock and fire. 1. Turn the power off and disconnect the projector from the wall socket. If the lamp is hot, avoid burns - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 50
in locations where water might splash on it, children can reach it, or near flammable materials. • Do not insert your hands into the projector after the lamp is removed. If you touch the optical components inside, it could cause color unevenness and distortion of the projected images. 7. Insert the - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 51
. A warning message is displayed asking if you want to reset the lamp timer. Highlight Reset and press MODE/ENTER on the projector or Enter on the remote control. The lamp time will be reset to '0'. CAUTION Do not reset if the lamp is not new or replaced as this could cause damage. 48 Maintenance - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 52
has shut down automatically. If you try to re-start the projector, it will shut down again. Please contact your dealer for assistance. Lamp events The projector has shut down automatically. If you try to reRed start the projector, it will shut down again. Please contact your dealer for assistance - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 53
control does not work Cause The battery is out of power. There is an obstacle between the remote control and the projector. You are too far away from the projector. Remedy Replace the battery with a new one. Remove the obstacle. Stand within 8 meters (26 feet) of the projector. 50 Troubleshooting - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 54
Specifications Projector specifications All specifications are subject to change without notice. General Product name Digital Projector Optical Resolution Display system Lens F/Number Lamp • PJD5152: 800 x 600 SVGA • PJD5352: 1024 x 768 XGA 1-CHIP DMD F = 2.6 to 2.78, f = 10.2 to 12.24 mm 220 - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 55
x 96.4 mm (H) x 225 mm (D) 225 96.4 Ceiling mount installation 189 264 60 66 Ceiling mount screws: M4 x 8 (Max. L = 10 mm) 119 67 Timing chart Supported timing for PC input Resolution 720 x 400 640 x 480 800 VGA_50 VGA_120 SVGA_60 SVGA_72 SVGA_75 SVGA_85 SVGA_50 SVGA_120 52 Specifications - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 56
.00 60 50 Displaying a 1080i(1125i)@60Hz or 1080i(1125i)@50Hz signal may result in slight image vibration. Supported timing for Video and S-Video inputs Video mode NTSC PAL SECAM PAL-M PAL-N PAL-60 NTSC4.43 Horizontal Frequency (MHz) 3.58 4.43 4.25 or 4.41 3.58 3.58 4.43 4.43 Specifications 53 - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 57
, magnetic, optical, chemical, manual or otherwise, without the prior written permission of ViewSonic Corporation. Disclaimer ViewSonic Corporation makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 58
Appendix IR control table Key Format Byte1 Byte2 Byte3 Byte4 Power NEC 83 F4 02 fd Freeze NEC 83 F4 03 fc Up Down NEC NEC 83 F4 0b f4 83 F4 0c f3 Left Right Color Mode NEC NEC NEC 83 F4 0d f2 83 F4 0e f1 83 F4 10 ef Volume+ Volume- NEC NEC 83 F4 82 7d 83 - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 59
Altitude Mode Off High Altitude Mode On High Altitude Mode status Lamp Mode Normal Lamp Mode Economic Lamp Mode status Front Table Rear Table Rear Ceiling Front Ceiling Projector position status Off TI 3D DLP Link 3D Sync Status Off On 3D Sync Invert Status CMD 0x06 0x14 0x00 0x04 0x00 0x34 0x11 - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 60
Contrast Brightness Aspect Ratio Auto Adjust Horizontal Position Vertical Position Color temperature Write Read Write Read Write Read Execute Write Read Write Read Write Read Contrast decrease Contrast increase Contrast ratio Brightness decrease Brightness increase Brightness Aspect ratio Auto - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 61
Write Read Write Read Write Read Write Read Blank on Blank off Blank status Decrease Increase Keystone status Brightest Cinema User 1 User 2 Daylight / Gaming ViewMatch Color Mode status Primary color R Primary color G Primary color B Primary color C Primary color M Primary color Y Primary color - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 62
Source input Write Input source VGA Input source VGA2 Input source Composite Input source S-VIDEO 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x00 0x60 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x08 0x68 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x05 0x65 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x06 0x66 - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 63
Lamp Time Error status Write Read Read Reset Lamp usage hour Lamp usage hour Read error status 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x01 0x00 0x62 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x15 0x01 0x63 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x0C 0x0D 0x66 60 Appendix - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 64
support or product service, see the table below or contact your reseller. Note : You will need the product serial number. Country/Region Australia/New Zealand Canada Europe Hong Kong India Web Site www.viewsonic.com.au www.viewsonic.com www.viewsoniceurope.com www.hk.viewsonic.com www.in.viewsonic - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 65
ViewSonic office for the warranty information. Lamp warranty subject to terms and conditions, verification and approval. Applies to manufacturer's installed lamp only. All accessory lamps to follow instructions supplied with the product. b. Operation outside of product specifications. c. Operation - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 66
meeting ViewSonic's specifications. i. Normal wear and tear. j. Any other cause which does not relate to a product defect. 3. Removal, installation, and set-up service charges. How to get service: 1. For information about receiving service under warranty, contact ViewSonic Customer Support (please - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 67
period of time. 4. Removal, installation, insurance, and set-up service charges. How to get service: For information about receiving service under warranty, contact ViewSonic Customer Support (Please refer to the attached Customer Support page). You will need to provide your product's serial - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 68
Acapulco Monterrey: GS Computación (Grupo Sesicomp) Global Product Services Progreso #6-A, Colo Centro Mar Caribe # 1987, Esquina 15-13-67-00 E-Mail. [email protected] Tijuana: FOR USA SUPPORT: STD ViewSonic Corporation Av Ferrocarril Sonora #3780 L-C 381 Brea Canyon Road, Walnut, - ViewSonic PJD5351 | PJD5152, PJD5352 User Guide (English) - Page 69
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
 |
 |
ViewSonic
®
IMPORTANT:
Please read this User Guide to obtain important information on install-
ing and using your product in a safe manner, as well as registering your product for
future service.
Warranty information contained in this User Guide will describe your
limited coverage from ViewSonic Corporation, which is also found on our web site
at http://www.viewsonic.com in English, or in specific languages using the Regional
selection box in the upper right corner of our website.
“Antes de operar su equipo lea cuidadosamente las instrucciones en este manual”
Model No. : VS13307 / VS13147
PJD5152 / PJD5352
DLP Projector
- User Guide
- Guide de l’utilisateur
- Bedienungsanleitung
- Guía del usuario
- Guida dell’utente
- Guia do usuário
- Användarhandbok
- Käyttöopas
- Руководство пользователя
-
使用手冊 (繁體)
-
使用手冊 (簡體)
-
사용자 안내서
- Podręcznik użytkownika
- Kullanιcι kιlavuzu