ViewSonic PJD7822HDL User Guide - Page 59

projector. Connect the new lamp's wire, compartment and make sure it fits in

Get ViewSonic PJD7822HDL PDF manuals and user guides View all ViewSonic PJD7822HDL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

4. Loosen the screw that secures the lamp. 5. Disconnect the lamp's wire connector from the projector, and then lift the handle so that it stands up. Use the handle to slowly pull the lamp out of the projector. CAUTION 2 1 3 • Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector. • Do not place the lamp in locations where water might splash on it, children can reach it, or near flammable materials. • Do not insert your hands into the projector after the lamp is removed. If you touch the optical components inside, it could cause color unevenness and distortion of the projected images. 6. Insert the new lamp into the lamp compartment and make sure it fits in the projector. Connect the new lamp's wire connector to the projector. 7. Tighten the screw that secures the lamp. CAUTION • Loose screw may cause a bad connection, which could result in malfunction. • Do not over tighten the screw. 8. Ensure the handle is fully laid flat and locked in place. 52

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
52
4.
Loosen the screw that secures the lamp.
5.
Disconnect the lamp’s wire connector from
the projector, and then lift the handle so that
it stands up. Use the handle to slowly pull
the lamp out of the projector.
CAUTION
•
Pulling it too quickly may cause the lamp to
break and scatter broken glass in the projector.
•
Do not place the lamp in locations where water
might splash on it, children can reach it, or
near flammable materials.
•
Do not insert your hands into the projector
after the lamp is removed. If you touch the
optical components inside, it could cause color
unevenness and distortion of the projected
images.
6.
Insert the new lamp into the lamp
compartment and make sure it fits in the
projector. Connect the new lamp’s wire
connector to the projector.
7.
Tighten the screw that secures the lamp.
CAUTION
•
Loose screw may cause a bad connection,
which could result in malfunction.
•
Do not over tighten the screw.
8.
Ensure the handle is fully laid flat and
locked in place.
1
2
3