Viper 5704 Owner Manual - Page 31

Pair Remote - remote case

Get Viper 5704 PDF manuals and user guides View all Viper 5704 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Pair Remote: Remote Pair is a process where the Responder LC and the system in the vehicle learn each others encrypted identification, securing their communication from intruders. Please note that your remote controls come pre-programmed from the factory. Prepare the vehicle system to be Paired with a new remote 1. Open at least one of the vehicle's doors. 2. Turn the key to the On position. 3. Within 5 seconds press and release 1 time the Control button on the Control Center. 4. Within 5 seconds, press and hold the Control button. The status LED will flash one time and the siren will chirp once to confirm the system is ready for remote pairing. 5. Release the Control button and proceed below. Note: If pairing does not result within 60 seconds, the system will exit and the siren will chirp. Prepare the new remote to be Paired with the system 1. Make sure the remote control is set for the desired Car 1 or Car 2 operation. 2. Perform the steps under Access menu items section to access the Pair Remote mode. 3. When the remote beeps 3 times and PAIR is displayed the remote is ready to pair. 4. Press and hold the button, the siren will chirp once and the remote will emit several tones to confirm successful pairing. SUCCESS is displayed and the remote returns to the main menu. Note: FAILED will be displayed and the remote will stay in the pair mode in case of an unsuccessful pairing. Check the system status and try again. 28 © 2011 Directed Electronics. All rights reserved.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
28
© 2011 Directed Electronics. All rights reserved.
28
Pair Remote:
Remote Pair is a process where the Responder LC and the system in
the vehicle learn each others encrypted identification, securing their
communication from intruders. Please note that your remote controls
come pre-programmed from the factory.
Prepare the vehicle system to be Paired with a new remote
1.
Open
at least one of the vehicle’s doors
.
2.
Turn
the key to the On position.
3.
Within 5 seconds
press
and release 1 time the Control button on
the Control Center.
4. Within 5 seconds,
press
and
hold
the Control button. The status
LED will flash one time and the siren will chirp once to confirm the
system is ready for remote pairing.
5.
Release
the Control button and proceed below.
Note:
If pairing does not result within 60 seconds, the system will exit
and the siren will chirp.
Prepare the new remote to be Paired with the system
1.
Make sure the remote control is set for the desired Car 1 or Car
2 operation.
2.
Perform the steps under
Access menu items
section to access the
Pair Remote mode.
3. When the remote beeps 3 times and
PAIR
is displayed the
remote is ready to pair.
4.
Press
and
hold
the
button, the siren will chirp once and
the remote will emit several tones to confirm successful pair-
ing.
SUCCESS
is displayed and the remote returns to the main
menu.
Note:
FAILED
will be displayed and the remote will stay in the pair
mode in case of an unsuccessful pairing. Check the system status and
try again.