Viper 5704 Owner Manual - Page 35

Trigger Zone Fault Report, Alarm Report when disarming - replacement remote

Get Viper 5704 PDF manuals and user guides View all Viper 5704 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Trigger Zone Fault Report When armed by remote command the system runs a status check of the alarm trigger zones. Faulty zones (usually caused by dome light delay or open trunk) are bypassed and reported via the control center LED and remote, while all other trigger zones remain active and are monitored to protect the vehicle. Should a faulty zone self correct (dome light turns off) it becomes active and is then monitored normally. The siren chirps once again a few seconds following the arming chirps as an audible alert, the control center LED flashes in groups to indicate the zone number. The remote will emit a single fault tone and play zone specific text that identifies the faulty zones. Alarm Report when disarming The most recent alarm triggers (if any) are reported when the alarm is disarmed via the remote control, siren chirps, parking light and control center LED flashes. The siren chirps 4 times (or 5 times if NPC On*), the parking lights flash 3 times, and the control center LED flashes in groups to indicate the last two zones that were triggered (see Table of Zones). The DISARM text is replaced by ALARM REPORT and text identifying the triggers. * See "Nuisance Prevention (NPC)" on page 33 for more details. 32 © 2011 Directed Electronics. All rights reserved.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
32
© 2011 Directed Electronics. All rights reserved.
32
Trigger Zone Fault Report
When armed by remote command the system runs a status check
of the alarm trigger zones. Faulty zones (usually caused by dome
light delay or open trunk) are bypassed and reported via the control
center LED and remote, while all other trigger zones remain active
and are monitored to protect the vehicle. Should a faulty zone self
correct (dome light turns off) it becomes active and is then monitored
normally.
The siren chirps once again a few seconds following the arming
chirps as an audible alert, the control center LED flashes in groups to
indicate the zone number. The remote will emit a single fault tone and
play zone specific text that identifies the faulty zones.
Alarm Report when disarming
The most recent alarm triggers (if any) are reported when the alarm is
disarmed via the remote control, siren chirps, parking light and control
center LED flashes. The siren chirps 4 times (or 5 times if NPC On*),
the parking lights flash 3 times, and the control center LED flashes in
groups to indicate the last two zones that were triggered (see Table
of Zones). The
DISARM
text is replaced by
ALARM REPORT
and text
identifying the triggers.
* See
“Nuisance Prevention (NPC)” on page 33
for more details.