Vtech Two Handset Cordless Answering System including a Cordless DECT 6.0 Headse - Page 11

Headset charger installation, Power on the headset, Headset charging

Get Vtech Two Handset Cordless Answering System including a Cordless DECT 6.0 Headset PDF manuals and user guides View all Vtech Two Handset Cordless Answering System including a Cordless DECT 6.0 Headset manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Getting started Headset charger installation Install the headset charger as shown below. Plug the small end of the headset charger power adapter into the power jack of the headset charger. Plug the large end of the headset charger power adapter into an electrical outlet not controlled by a wall switch. Headset charger Power on the headset Power on the headset before use. Place the headset in the headset charger or press and hold for two seconds. The light flashes three times in blue and you hear three beeps when the headset is being powered on. If the headset will not be used for a long time, press and hold for two seconds to power off the headset. The light flashes three times in red and you hear three beeps when the headset is being powered off. Headset charging After installing the headset charger, charge the headset as shown below. The headset is fully charged after three hours of continuous charging. If the light does not turn on while charging, you need to charge the headset without interruption for at least 15 minutes to give the headset enough charge to use for a short time. For best performance, keep the headset in the headset charger when not in use. See the table on page 62 for battery operating times. 1. Place the tip of the headset in the small cradle on the headset charger. The headset battery is not replaceable.  2. The magnet holds the top of the headset in place. The light turns on when charging.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
7
Getting started
Headset charger installation
Install the headset charger as shown below.
Headset charger
Plug the small end of
the headset charger
power adapter into
the power jack of the
headset charger.
Plug the large end of the
headset charger power
adapter into an electrical
outlet not controlled by a
wall switch.
Power on the headset
Power on the headset before use. Place the headset in the headset charger
or press and hold
for two seconds. The
light flashes three times in blue
and you hear three beeps when the headset is being powered on.
Headset charging
After installing the headset charger, charge the headset as shown below. The
headset is fully charged after three hours of continuous charging. If the
light does not turn on while charging, you need to charge the headset without
interruption for at least 15 minutes to give the headset enough charge to
use for a short time. For best performance, keep the headset in the headset
charger when not in use. See the table on page 62 for battery operating times.
1. Place the tip of
the headset in the
small cradle on
the headset charger.
2. The magnet holds
the top of the
headset in place.
The
light turns
on when charging.
If the headset will not be used for a long time, press and hold
for two
seconds to power off the headset. The
light flashes three times in red and
you hear three beeps when the headset is being powered off.
The headset battery is not replaceable.