Weider 950 English Manual
Weider 950 Manual
 |
View all Weider 950 manuals
Add to My Manuals
Save this manual to your list of manuals |
Weider 950 manual content summary:
- Weider 950 | English Manual - Page 1
CUSTOMER HOT LINE: 1-800-999-3756 Mon.-Fri., 6 a.m.-6 p.m. MST CAUTION Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference. USER'S MANUAL Visit our website at www.weiderfitness.com new products, prizes, fitness tips, and much more! - Weider 950 | English Manual - Page 2
5 ADJUSTMENTS 15 WEIGHT RESISTANCE CHART 17 CABLE DIAGRAM 18 TROUBLESHOOTING AND MAINTENANCE 19 ORDERING REPLACEMENT PARTS Back Cover LIMITED WARRANTY Back Cover Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the center of this manual. Remove the PART - Weider 950 | English Manual - Page 3
the weight system. 1. Read all instructions in this manual and in the accompanying literature before using the weight system. Use the weight system only as described in this manual. 11. Make sure that the cables remain on the pulleys at all times. If the cables bind while you are exercising, stop - Weider 950 | English Manual - Page 4
or improve your cardiovascular system, the WEIDER® 950 weight system will help you to achieve the results you want. For your benefit, read this manual carefully before using the weight system. If you have questions after reading this manual, please call our Customer Service Department toll-free at - Weider 950 | English Manual - Page 5
manual is designed to ensure that the weight system can be assembled successfully by anyone. However, it is important to realize that the versatile weight system all parts as you assemble them, unless instructed to do otherwise. • As you assemble the weight system, make sure all parts are oriented - Weider 950 | English Manual - Page 6
M8 x 70mm Bolt (51) and an M8 Nylon Locknut (61). Slide the Weight Carriage (26) onto the Rear Upright (3). 4. Attach the Top Frame (5) to Top Frame (5) to the Rear Upright (3) with two M8 x 66mm Bolts (60), the Support Plate (25), and an M8 Nylon Locknut (61). Tighten all of the M8 Nylon Locknuts - Weider 950 | English Manual - Page 7
ARM ASSEMBLY 5 5. Press two 25mm x 50mm Inner Cap (42) into the top of the Press Frame (9). Press two 50mm Square Inner Caps (44) into the ends of the Press Frame. Orient the Press Frame (9) with the bracket on the side shown. Attach the Press Frame to the Top Frame (5) with an M10 x 125mm Bolt ( - Weider 950 | English Manual - Page 8
18 for proper cable routing. Locate the High Cable (35). Route the eyelet end of the Cable up through the Top Frame (5) and around a Pulley (39). Attach the Pulley inside the Top Frame with an M10 x 65mm Grade 5 Bolt (73), two M10 Washers (55), two M10 Spacers (74), and an M10 Nylon - Weider 950 | English Manual - Page 9
bracket on the Weight Carriage (26) with an M10 Nylon Locknut (56). 35 75 26 56 13. Locate the Arm Cable (36). Slide the Cable onto 13 the hook on the Right Arm (10). 36 Hook 10 14. Wrap the Arm Cable (36) around a "V"-Pulley 14 (38). Attach the Pulley and a Long Cable - Weider 950 | English Manual - Page 10
Bolt (69) and an M10 Nylon Locknut (56). Be sure the Cable Trap is turned to hold the Cable in the groove of the Pulley. Attach the Pulley Bracket (30) to the bracket on the Front Upright (4) with an M10 x 78mm Bolt (71) and an M10 Nylon Locknut (56). 17. Slide the - Weider 950 | English Manual - Page 11
bracket on the Base (1) with the ball on the side shown. Attach a Pulley (39) inside the bracket on the Base (1) with an M10 x 45mm Bolt (37) through the hole in the 22 Front Upright (4) and around a Pulley (39). Attach the Pulley and a Cable Trap (41) inside the brack- et on the Upright with - Weider 950 | English Manual - Page 12
56 77 41 37 39 24. Wrap the Low Cable (37) around a Pulley (39). 24 Attach the Pulley inside the bracket on the Base (1) with an M10 x 45mm Bolt ( Be sure the Cable Trap is turned to hold the Cable in the groove of the Pulley. 26. Attach the Low Cable (37) inside the Base (1) 26 with an M10 - Weider 950 | English Manual - Page 13
SEAT ASSEMBLY 27 27. Press two 38mm Square Inner Caps (48) into the ends of the Seat Frame (6) and the Leg Lever (7). Attach the Eyebolt (53) to the Leg Lever (7) with an M10 Washer (55) and an M10 Nylon Locknut (56). Lubricate the M8 x 66mm Bolt (60). Attach the Leg Lever (7) to the Seat Frame - Weider 950 | English Manual - Page 14
explained in ADJUSTMENTS, on the next page. Before using the weight system, pull each cable a few times to make sure that the cables move smoothly over the pulleys. If one of the cables does not move smoothly, find and correct the problem. IMPORTANT: If the cables are not properly routed, they may - Weider 950 | English Manual - Page 15
each side of the weight tube on the Weight Carriage (26). Be sure that the weights are pushed against the weight stops. Note: Due to the cables and pulleys, the actual amount of resistance at each exercise station may vary from the amount of weight used. Use the WEIGHT RESISTANCE CHART on page 17 to - Weider 950 | English Manual - Page 16
). Be sure the bracket on the Curl Post wraps around the round tubes on the the Seat Frame. ATTACHING THE LEG LEVER TO THE LOW PULLEY STATION To use the Leg Lever (7), the seat must be attached to the front upright (see ATTACHING AND REMOVING THE SEAT, on the previous page). Attach - Weider 950 | English Manual - Page 17
WEIGHT RESISTANCE CHART This chart shows the approximate weight resistance at each weight station. The column labeled "WEIGHT" refers to the amount of weight, in pounds, placed on the weight carriage. The weight resistance shown for the butterfly arm station 142 LEG LEVER HIGH PULLEY (lbs.) 14 20 - Weider 950 | English Manual - Page 18
the diagrams to make sure that the cables and the cable traps have been assembled correctly. If the cables have not been correctly routed, the weight system will not function properly and damage may occur. The numbers show the correct route for each cable. Make sure that the cable traps do not - Weider 950 | English Manual - Page 19
TROUBLESHOOTING AND MAINTENANCE TIGHTENING THE CABLES Woven cable, the type of cable used on the weight system, can stretch slightly when it is first used. If there is slack in the cables before resistance is felt, the cables should be tightened. Slack can be removed by moving a Pulley (39) and - Weider 950 | English Manual - Page 20
PART IDENTIFICATION CHART-Model No. WESY13820 R0902B M10 Nylon Locknut (56) M8 Nylon Locknut (61) M6 Nylon Locknut (58) 19mm Round Inner Cap (49) Dome Cap (47) 25mm - Weider 950 | English Manual - Page 21
M8 Washer (76) M6 x 16mm Bolt (59) M10 x 20mm Bolt (75) M6 x 43mm Bolt (57) M10 Washer (55) M6 Washer (63) M10 x 45mm Bolt (68) M10 x 48mm Bolt (77) M6 x 50mm Screw (64) M6 x 50mm Carriage Bolt (62) M10 x 55mm Bolt (69) M6 x 63mm Screw (70) M8 x 63mm Bolt (78) M10 x 65mm Bolt (79) M10 x 65mm - Weider 950 | English Manual - Page 22
Support Plate Weight Carriage Weight Stop Arm Pin Arm Latch Pulley Bracket Curl Frame Knob Seat Frame Knob Lat Bar Grip Arm Grip High Cable Arm Cable Low Cable "V"-Pulley Pulley Bolt M10 x 23mm Spacer Grease Packet User's Manual Exercise Guide Note: "#" indicates a non-illustrated part. - Weider 950 | English Manual - Page 23
EXPLODED DRAWING-Model No. WESY13820 R0902B 33 13 12 39 41 55 42 56 43 9 54 55 77 56 35 67 46 39 74 55 56 33 44 11 60 41 56 41 39 56 25 39 14 77 39 56 5 36 44 68 61 74 39 73 55 72 71 56 30 61 3 71 56 69 56 30 38 40 29 61 56 76 42 76 78 38 40 69 4 16 70 63 58 10 - Weider 950 | English Manual - Page 24
(WEIDER® 950 weight system) • The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and EXPLODED DRAWING attached at the center of this manual) , at ICON's option, the product through one of its authorized service centers. All repairs for which warranty claims are made must be pre
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
 |
 |
USER'S MANUAL
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Model No. WESY13820
Model Number Decal (under seat)
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you have
questions, or if there are missing
parts, we will guarantee complete
satisfaction through direct assis-
tance from our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT LINE. The
technicians on our customer hot
line will provide immediate assis-
tance, free of charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
Visit our website at
www.weiderfitness.com
new products, prizes,
fitness tips, and much more!