Weider Victory X25 Power Guide English Manual - Page 12

Dimple

Page 12 highlights

PAGE 11 WEIDER SPORTING GOODS 4 CED 05 86 8 41 38 \k FLAT SIDE ""•••01 91 CABLE END FITTING Assemble a 112" O.D. X-3/8" LONG METAL BUSHING (86) onto the 5/16" X 2" CARRIAGE BOLT (105), followed with the ANGLE PLATE BRACKET (38). Next, assemble the Loop end of the LAT CABLE.(8) (This Cable has a large RubberBallandLoop on One endanda Loop on the other ehd.) onto the Bolt malting sure to turn the Cable SO:that the flat side of the Cable end fitting is against the Angle Plate Bracket. Secure with a 5116" NYLON LOCK NUT (41). Lay the unassembled end of the Cable aside for completion in a later Step. The WEIGHT SELECTOR PIN (82) has two dimples. When Inserting the Selector Pin into the WEIGHT PLATES (5), turn the Pin so that the dimples are down. When fully Inserted, turn the Pin so that the handle portion is turned down. This will lock the Pin into the Weight Plates. Be sure to fully insert the Pin so it passes through both sides of the WEIGHT SELECTOR TUBE (6). MAKE SURE THE SELECTOR PIN IS IN THE LOCKED POSITION. BEFORE BEGINNING ANY EXERCISE! Insert the WEIGHT SELECTOR PIN (82) into the Weight Stack at the bottom Plate until essembly. is complete and the Cable system has been adjusted forproper tensioning. Remove the WEIGHT PLATE DECALS (91) from the backing sheet and affix to the edge of the WEIGHT PLATES (5) just to the side ofthe Pinning Slots. Decals shouldprogress from the lightest Weight on the top Plate to the heaviest Weight at the bottom - Begin with Decal 12.5 on the top Plate andproceed down to 125 on the bottom Plate. DIMPLE HANDLE IN THE INSERT POSITION ----I HANDLE POSITION • DOWN IN THE LOCKED POSITION

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32

PAGE
11
WEIDER
SPORTING
GOODS
05
4
CED
86
38
8
41
\
k
FLAT
SIDE
""•••01
91
CABLE
END
FITTING
Assemble
a
112"
O.D.
X
-
3/8"
LONG
METAL
BUSHING
(86)
onto
the
5/16"
X
2"
CARRIAGE
BOLT
(105),
followed
with
the
ANGLE
PLATE
BRACKET
(38).
Next,
assemble
the
Loop
end
of
the
LAT
CABLE.
(8)
(This
Cable
has
a
large
Rubber
Ball
and
Loop
on
One
end
and
a
Loop
on
the
other
ehd.)
onto
the
Bolt
malting
sure
to
turn
the
Cable
SO:
that
the
flat
side
of
the
Cable
end
fi
tting
is
against
the
Angle
Plate
Bracket.
Secure
with
a
5116"
NYLON
LOCK
NUT
(41).
Lay
the
unassembled
end
of
the
Cable
aside
for
completion
in
a
later
Step.
The
WEIGHT
SELECTOR
PIN
(82)
has
two
dimples.
When
Inserting
the
Selector
Pin
into
the
WEIGHT
PLATES
(5),
turn
the
Pin
so
that
the
dimples
are
down.
When
fully
Inserted,
turn
the
Pin
so
that
the
handle
portion
is
turned
down.
This
will
lock
the
Pin
into
the
Weight
Plates.
Be
sure
to
fully
insert
the
Pin
so
it
passes
through
both
sides
of
the
WEIGHT
SELECTOR
TUBE
(6).
MAKE
SURE
THE
SELECTOR
PIN
IS
IN
THE
LOCKED
POSITION.
BEFORE
BEGINNING
ANY
EXERCISE!
Insert
the
WEIGHT
SELECTOR
PIN
(82)
into
the
Weight
Stack
at
the
bottom
Plate
until
essembly.
is
complete
and
the
Cable
system
has
been
adjusted
for
proper
tensioning.
Remove
the
WEIGHT
PLATE
DECALS
(91)
from
the
backing
sheet
and
affix
to
the
edge
of
the
WEIGHT
PLATES
(5)
just
to
the
side
of
the
Pinning
Slots.
Decals
should
progress
from
the
lightest
Weight
on
the
top
Plate
to
the
heaviest
Weight
at
the
bottom
-
Begin
with
Decal
12.5
on
the
top
Plate
and
proceed
down
to
125
on
the
bottom
Plate.
DIMPLE
HANDLE
IN
THE
INSERT
POSITION
----I
HANDLE
POSITION
DOWN
IN
THE
LOCKED
POSITION