Weslo 750 Instruction Manual - Page 10

Locate the Short Cable 47.

Get Weslo 750 PDF manuals and user guides View all Weslo 750 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

14. Wrap the High Cable (50) over a 90mm Pulley 14 (34). Attach the Pulley and two Finger Guards (35) to the Top Frame (4) with an M10 x 46mm Bolt (53) and an M10 Nylon Locknut (68). 15. Attach the end of the High Cable (50) to the 15 Small "U"-bracket (11) with an M8 Washer (71) and an M8 Nylon Locknut (69). Note: Do not completely tighten the Locknut; it should be threaded onto the Cable so that two threads 71 show past the Locknut, as shown in the inset drawing. 69 Attach the Small "U"-bracket (11) to the Weight Tube (12) with an M8 x 45mm Bolt (60) and an M8 Nylon Locknut (69). Do not overtighten the Locknut; the Weight Tube must be able to pivot in the Small "U"-bracket. 53 35 4 34 35 68 50 60 11 12 50 11 69 16. Locate the Press Cable (49). Slide the Cable 16 onto the hook on the Left Arm (7). Hook 49 17. Apply grease to an M10 x 78mm Bolt (54). Attach 17 the Pulley Arm (38) to the Upright (3) with the Bolt and an M10 Nylon Locknut (68). Do not over- tighten the Locknut; the Pulley Arm must be able to pivot easily. Wrap the Press Cable (49) over a 90mm Pulley (34). Attach the Pulley, a Cable Trap (36), an M10 Washer (70), and two Finger Guards (35) to the indicated side of a Pulley Arm (38) with an M10 x 52mm Bolt (52) and an M10 Nylon Locknut (68). Make sure that the Cable Trap is oriented to hold the Cable in the groove of the Pulley. 10 7 3 54 68 35 36 38 52 70 34 35 49 18. Wrap the Press Cable (49) under a 90mm Pulley 18 (34). Attach the Pulley and two Finger Guards (35) to the Double "U"-bracket (42) with an M10 x 46mm Bolt (53) and an M10 Nylon Locknut (68). 19. Apply grease to an M10 x 78mm Bolt (54). Attach 19 the Pulley Arm (38) to the Upright (3) with the Bolt and an M10 Nylon Locknut (68). Do not over- tighten the Locknut; the Pulley Arm must be able to pivot easily. Wrap the Press Cable (49) over a 90mm Pulley (34). Attach the Pulley, a Cable Trap (36), an M10 Washer (70), and two Finger Guards (35) to the indicated side of a Pulley Arm (38) with an M10 x 52mm Bolt (52) and an M10 Nylon Locknut (68). Make sure that the Cable Trap is oriented to hold the Cable in the groove of the Pulley. 49 34 35 68 35 53 42 52 54 38 35 36 68 49 34 70 35 68 3 20. Slide the end of the Press Cable (49) onto the hook on the Right Arm (6). 20 49 6 21. Locate the Short Cable (47). Attach the eyelet 21 on the Cable to the Base (1) with an M10 x 70mm Bolt (57), an M10 Washer (70), and an M10 Nylon Locknut (68). Do not overtighten the Locknut. 70 68 1 57 47 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
11
19. Apply grease to an M10 x 78mm Bolt (54). Attach
the Pulley Arm (38) to the Upright (3) with the Bolt
and an M10 Nylon Locknut (68).
Do not over-
tighten the Locknut; the Pulley Arm must be
able to pivot easily.
Wrap the Press Cable (49) over a 90mm Pulley
(34). Attach the Pulley, a Cable Trap (36), an M10
Washer (70), and two Finger Guards (35) to the
indicated side of a Pulley Arm (38) with an M10 x
52mm Bolt (52) and an M10 Nylon Locknut (68).
Make sure that the Cable Trap is oriented to
hold the Cable in the groove of the Pulley.
18. Wrap the Press Cable (49) under a 90mm Pulley
(34). Attach the Pulley and two Finger Guards
(35) to the Double “U”-bracket (42) with an M10 x
46mm Bolt (53) and an M10 Nylon Locknut (68).
34
53
68
49
35
42
35
18
35
36
49
52
38
68
68
3
54
34
35
70
19
10
16.
Locate the Press Cable (49).
Slide the Cable
onto the hook on the Left Arm (7).
17. Apply grease to an M10 x 78mm Bolt (54). Attach
the Pulley Arm (38) to the Upright (3) with the Bolt
and an M10 Nylon Locknut (68).
Do not over-
tighten the Locknut; the Pulley Arm must be
able to pivot easily.
Wrap the Press Cable (49) over a 90mm Pulley
(34). Attach the Pulley, a Cable Trap (36), an M10
Washer (70), and two Finger Guards (35) to the
indicated side of a Pulley Arm (38) with an M10 x
52mm Bolt (52) and an M10 Nylon Locknut (68).
Make sure that the Cable Trap is oriented to
hold the Cable in the groove of the Pulley.
15. Attach the end of the High Cable (50) to the
Small “U”-bracket (11) with an M8 Washer (71)
and an M8 Nylon Locknut (69).
Note: Do not
completely tighten the Locknut; it should be
threaded onto the Cable so that two threads
show past the Locknut, as shown in the inset
drawing.
Attach the Small “U”-bracket (11) to the Weight
Tube (12) with an M8 x 45mm Bolt (60) and an
M8 Nylon Locknut (69).
Do not overtighten the
Locknut; the Weight Tube must be able to
pivot in the Small “U”-bracket.
14. Wrap the High Cable (50) over a 90mm Pulley
(34). Attach the Pulley and two Finger Guards
(35) to the Top Frame (4) with an M10 x 46mm
Bolt (53) and an M10 Nylon Locknut (68).
68
50
34
35
35
4
53
14
11
71
60
69
12
15
7
35
35
34
68
16
17
20. Slide the end of the Press Cable (49) onto the
hook on the Right Arm (6).
49
6
20
21.
Locate the Short Cable (47).
Attach the eyelet
on the Cable to the Base (1) with an M10 x
70mm Bolt (57), an M10 Washer (70), and an
M10 Nylon Locknut (68).
Do not overtighten the
Locknut.
57
70
68
47
1
21
50
69
11
49
Hook
70
49
36
38
52
54
3