Whirlpool WFG975H0H Installation Instructions - Page 19

To Convert Surface Burners Propane Gas to Natural, To Convert Oven Bake Burner Propane Gas to,

Get Whirlpool WFG975H0H PDF manuals and user guides View all Whirlpool WFG975H0H manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

3. Remove plastic cover from gas pressure regulator cap. 4. Turn gas pressure regulator cap counterclockwise with a 5/8" (1.6 cm) combination wrench to remove. NOTE: Do not remove the spring beneath the cap. Side view before A LP 3. Apply masking tape to the end of a 9/32" (7 mm) nut driver to help hold the gas orifice spud in the nut driver while changing it. Press nut driver down onto the gas orifice spud and remove by turning it counterclockwise and lifting out. Set gas orifice spud aside. AB D C B D E LP A. Igniter electrode B. Orifice spud C. Orifice spud holder D. Screws 4. Gas orifice spuds are stamped with a number on the side or top. Replace the propane gas orifice spud with the correct Natural gas orifice spud. NG NG C Side view after A. Plastic cover B. Gas pressure regulator cap with hollow end facing out C. Gas pressure regulator cap with solid end facing out D. Washer E. Gas pressure regulator cap 5. Turn over the gas pressure regulator cap and reinstall on regulator so that the solid end faces out and the marking " NG" is facing the direction shown in the above drawing. 6. Replace plastic cover over gas pressure regulator cap. To Convert Surface Burners (Propane Gas to Natural Gas) 1. Remove burner cap. 2. Remove the burner base. A B E D C A. Burner cap B. Burner base C. Alignment pins D. Igniter electrode E. Gas tube opening XXX XXX A A. Stamped number Refer to the following chart for the correct Natural gas orifice spud placement. Natural Gas Orifice Spud Chart Burner Rating Size (mm) ID Number 18,000 BTU 2.00 200AM 17,000 BTU 1.96 196AM 15,000 BTU 1.80 180AM 9,500 BTU 1.40 140AM 8,000 BTU 1.30 130AM 5,000 BTU 1.00 100AM NOTE: Refer to the model/serial/rating plate located on the oven frame behind the top right-hand side of the oven door for proper sizing of spuds for each burner location. 5. Place propane gas orifice spuds in the orifice spud bag. IMPORTANT: Keep the propane gas orifice spuds in case of reinstallation with propane gas. 6. Replace the burner base. 7. Replace burner cap. 8. Repeat steps 1 to 7 for the remaining burners. To Convert Oven Bake Burner (Propane Gas to Natural Gas) 1. Remove the oven racks and the oven door. See the "Oven Door" section. 2. Remove two screws and washers at the rear of the oven bottom. 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
19
°
3.
Remove plastic cover from gas pressure regulator cap.
4.
Turn gas pressure regulator cap counterclockwise with a
5/8" (1.6 cm) combination wrench to remove.
NOTE
: Do not remove the spring beneath the cap.
5.
Turn over the gas pressure regulator cap and reinstall on
regulator so that the solid end faces out and the marking
“
NG” is facing the direction shown in the above drawing.
6.
Replace plastic cover over gas pressure regulator cap.
To Convert Surface Burners (Propane Gas to Natural
Gas)
1.
Remove burner cap.
2.
Remove the burner base.
3.
Apply masking tape to the end of a 9/32" (7 mm) nut driver to
help hold the gas orifice spud in the nut driver while changing
it. Press nut driver down onto the gas orifice spud and remove
by turning it counterclockwise and lifting out. Set gas orifice
spud aside.
4.
Gas orifice spuds are stamped with a number on the side or
top. Replace the propane gas orifice spud with the correct
Natural gas orifice spud.
Refer to the following chart for the correct Natural gas orifice
spud placement.
Natural Gas Orifice Spud Chart
Burner Rating
Size (mm)
ID Number
18,000 BTU
2.00
200AM
17,000 BTU
1.96
196AM
15,000 BTU
1.80
180AM
9,500 BTU
1.40
140AM
8,000 BTU
1.30
130AM
5,000 BTU
1.00
100AM
NOTE:
Refer to the model/serial/rating plate located on the oven
frame behind the top right-hand side of the oven door for proper
sizing of spuds for each burner location.
5.
Place propane gas orifice spuds in the orifice spud bag.
IMPORTANT:
Keep the propane gas orifice spuds in case
of reinstallation with propane gas.
6.
Replace the burner base.
7.
Replace burner cap.
8.
Repeat steps 1 to 7 for the remaining burners.
To Convert Oven Bake Burner (Propane Gas to
Natural Gas)
1.
Remove the oven racks and the oven door. See the “Oven
Door” section.
2.
Remove two screws and washers at the rear of the oven
bottom.
A
B
C
D
Side view before
Side view after
E
NG
LP
LP
NG
A. Plastic cover
B. Gas pressure regulator cap with hollow end facing out
C. Gas pressure regulator cap with solid end facing out
D. Washer
E. Gas pressure regulator cap
A. Burner cap
B. Burner base
C. Alignment pins
D. Igniter electrode
E. Gas tube opening
D
E
C
B
A
A
B
C
D
A. Igniter electrode
B. Orifice spud
C. Orifice spud holder
D. Screws
A. Stamped number
X
X
X
A
X
X
X