Whirlpool WFG975H0H Installation Instructions - Page 20

A. Screws, B. Oven bottom, A. Bake burner, B. Screws, A. Orifice spud, A. Oven Orifice

Get Whirlpool WFG975H0H PDF manuals and user guides View all Whirlpool WFG975H0H manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

3. Lift the rear of the oven bottom up and back until the front of the panel is away from the front frame. Remove from oven and set it aside on a covered surface. A B 6. Apply masking tape to the end of a 3/8" (9.5 mm) nut driver to help hold the gas orifice spud in the nut driver while changing it. Press nut driver down onto the gas orifice spud and remove by turning the propane gas bake burner orifice spud counterclockwise to remove. The spud will be stamped with a "56". 7. Replace the "56" spud with a "47" spud. Install the Natural gas bake burner orifice spud, turning it clockwise until snug. IMPORTANT: Do not overtighten. A A. Screws B. Oven bottom 4. Remove two screws from the bake burner. 5. Slide the front of the bake burner to the side to remove tab from front of oven. Lift the back of the bake burner off the oven orifice, and set the bake burner aside. Do not disconnect the wire. A B A. Bake burner B. Screws A. Orifice spud 8. Position the back of the bake burner over the oven orifice, and then align the holes for the screws. 9. Reattach the bake burner with two screws. 10. Position the front of the oven bottom panel toward the front frame, and then lower the rear of the oven bottom panel into the oven. 11. Reattach the oven bottom panel with two screws and two washers. A A. Oven Orifice 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
20
3.
Lift the rear of the oven bottom up and back until the front of
the panel is away from the front frame. Remove from oven
and set it aside on a covered surface.
4.
Remove two screws from the bake burner.
5.
Slide the front of the bake burner to the side to remove tab
from front of oven. Lift the back of the bake burner off the
oven orifice, and set the bake burner aside. Do not
disconnect the wire.
6.
Apply masking tape to the end of a 3/8" (9.5 mm) nut driver
to help hold the gas orifice spud in the nut driver while
changing it. Press nut driver down onto the gas orifice spud
and remove by turning the propane gas bake burner orifice
spud counterclockwise to remove. The spud will be stamped
with a “56”.
7.
Replace the “56” spud with a “47” spud. Install the Natural
gas bake burner orifice spud, turning it clockwise until snug.
IMPORTANT:
Do not overtighten.
8.
Position the back of the bake burner over the oven orifice,
and then align the holes for the screws.
9.
Reattach the bake burner with two screws.
10.
Position the front of the oven bottom panel toward the front
frame, and then lower the rear of the oven bottom panel into
the oven.
11.
Reattach the oven bottom panel with two screws and two
washers.
A
B
A. Screws
B. Oven bottom
A
B
A. Bake burner
B. Screws
A
A. Orifice spud
A
A. Oven Orifice