Xerox 3250D User Guide - Page 44

Installing additional memory, Precautions to take when installing memory, Installing a memory module - device not recognized

Get Xerox 3250D - Phaser B/W Laser Printer PDF manuals and user guides
UPC - 095205740929
View all Xerox 3250D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

10 Installing additional memory Your machine is a full-featured model that has been optimized to meet most of your printing needs. Recognizing that each user may have different requirements, however, Xerox makes additional memory available to enhance your machine's capabilities. This chapter includes: • Precautions to take when installing memory • Installing a memory module 2 Open the expansion memory cover. Precautions to take when installing memory Disconnect the power cord Never remove the expansion memory cover while the power is turned on. To avoid the possibility of an electrical shock, always disconnect the power cord when installing or removing ANY internal or external accessories. Discharge static electricity The control board and internal accessories (network interface card or memory module) are sensitive to static electricity. Before installing or removing any internal accessories, discharge static electricity from your body by touching something metal, such as the metal back plate on any device plugged into a grounded power source. If you walk around before finishing the installation, repeat this procedure to discharge any static electricity again. Installing a memory module Your machine has a dual in-line memory module (DIMM). Use this memory module slot to install additional memory. When you are expanding the memory capacity, you can add a memory module to the vacant memory slot. Your machine has 32 MB memory, and you can add a 128 MB memory module. Order information is provided for optional memory module. (See "Accessories" on page 7.1.) 1 Turn the machine off and unplug all cables from the machine. 3250-008 3 Take out a new memory module from the plastic bag. 4 Holding the memory module by the edges, align the memory module on the slot at about a 30-degree tilt. Make sure that the notches of the module and the grooves on the slot fit each other. 3250-006 Note The notches and grooves illustrated above may not match those on an actual memory module and its slot. 5 Press the memory module into the slot with care until you hear a "click". 3250-007 Caution Do not press too hard or the module may be damaged. If the module does not seem to fit into the slot properly, carefully try the previous procedure again. 6 Replace the expansion memory cover. 7 Reconnect the power cord and printer cable, and turn the machine on. Note To release the memory module, pull the two tabs on the sides of the slot outwards, then the module springs out. 10.1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
10
.1
<
Installing additional memory>
10
Installing additional memory
Your machine is a full-featured model that has been optimized to meet
most of your printing needs. Recognizing that each user may have
different requirements, however, Xerox makes additional memory
available to enhance your machine’s capabilities.
This chapter includes:
•
Precautions to take when installing memory
•
Installing a memory module
Precautions to take when installing memory
Disconnect the power cord
Never remove the expansion memory cover while the power is turned on.
To avoid the possibility of an electrical shock, always disconnect the
power cord when installing or removing ANY internal or external
accessories.
Discharge static electricity
The control board and internal accessories (network interface card or
memory module) are sensitive to static electricity. Before installing or
removing any internal accessories, discharge static electricity from your
body by touching something metal, such as the metal back plate on any
device plugged into a grounded power source. If you walk around before
finishing the installation, repeat this procedure to discharge any static
electricity again.
Installing a memory module
Your machine has a dual in-line memory module (DIMM). Use this
memory module slot to install additional memory.
When you are expanding the memory capacity, you can add a memory
module to the vacant memory slot. Your machine has 32 MB memory,
and you can add a 128 MB memory module.
Order information is provided for optional memory module. (See
"Accessories" on page 7.1.)
1
Turn the machine off and unplug all cables from the machine.
2
Open the expansion memory cover.
3
Take out a new memory module from the plastic bag.
4
Holding the memory module by the edges, align the memory
module on the slot at about a 30-degree tilt. Make sure that the
notches of the module and the grooves on the slot fit each other.
Note
The notches and grooves illustrated above may not match
those on an actual memory module and its slot.
5
Press the memory module into the slot with care until you hear a
“click”.
Caution
Do not press too hard or the module may be damaged. If
the module does not seem to fit into the slot properly,
carefully try the previous procedure again.
6
Replace the expansion memory cover.
7
Reconnect the power cord and printer cable, and turn the machine
on.
Note
To release the memory module, pull the two tabs on the
sides of the slot outwards, then the module springs out.
3250-008
3250-006
3250-007