Yamaha IIs Owner's Manual - Page 37
TrgSens1] & [TrgSens2] Trigger Basics, Input, Curve, PadCtl
UPC - 086792645445
View all Yamaha IIs manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 37 highlights
Edit Section [TrgSens1] & [TrgSens2] Trigger Basics These two pages contain settings to set how your playing strength (trigger signal level) is converted into velocity for MIDI Note On events. In general, hitting the pad hard produces a large velocity value, and the resulting voices sound loudly. [TrgSens1] Type Gain Curve PadCtrl Input=1 RHP 32 3 - pitch 1 2 3 4 5 [TrgSens2] Level(100%) Input=16 20% to 100% Velocity(127) 32 to 127 6 7 1 Input= Select a target trigger input (1 to 16). 2 Type Select the pad type for the target input 1. The list below shows the pad types that can be set for the connected pads or trigger pickups. ❏ Settings: Refer to the following table. DTXTREME IIs Pad Types KP KP65/60/80S/80 TP-1/Snr TP120SD/100 (*1) TP-1/Tom TP120SD/100 (*1) TP-2/Snr TP65S (*1) TP-2/Tom TP65S (*1) TP-3 TP80S/80/65/60 (*2) RHP RHP120SD/120/100/80 RHP Kick KP120 PCY-1 PCY150S PCY-2 PCY130S/130/65S/65/80S/80 PCY-3 PCY80S/80/65S/65/60/10 RHH RHH130 (*3) BP BP80 DT Snare DT10/20 drum trigger for snare drum DT HiTom DT10/20 drum trigger for high toms DT LoTom DT10/20 drum trigger for low toms DT Kick DT10/20 drum trigger for bass drum TRG Snr Generic trigger pickup for snare drum TRG HTom Generic trigger pickup for high toms TRG LTom Generic trigger pickup for low toms TRG Kick Generic trigger pickup for bass drum *1 "TP-1/Snr" and "TP-2/Snr" set more sensitivity to the rim 2 for easy closed rimshot play. "TP-1/Tom" and "TP-2/Tom" set the same sensitivity to both rims 1 and 2. *2 "TP-3" will produce a voice assigned to the rim 1 when the pad rim is hit. *3 "RHH" also supports the TP65S pad. Rim 2 TP120SD/ TP100 TP65S Rim 1 Rim 1 Rim 2 3 Gain Set the input gain for the pad type 2. The larger the value, the more sensitive the pad becomes. ❏ Settings: 0~63 4 Curve Set the velocity curve for the change of trigger signal levels. For larger values, the pad must be hit harder to produce the loudest sound. ❏ Settings: 1~5 5 PadCtl When using a TP120SD or TP100 pad for the snare drum or tom (connected to trigger inputs 1 to 6), you can use the pad controller to adjust the drum tone. Specify a voice parameter (page 48) adjusted by the pad controller. Select a value that ends with an "R" letter, for simultaneous control for both pad and rim 1 voices. ❏ Settings: off (no effect), pitch (R) (Tuning), volume (R), voice (R), pan (R), layer (R), filter (R), Q (R), attack (R), decay (R), decay R+ (see note), wave 1 (Layer 1 voice)*, wave 2*, XSfilter*, XSdecay*, balance* * Controllable when Type=XtrSnr is selected in voice settings. n The decay+R value can continuously adjust the voice decay rate and switch to another specific voice (strainer-off tone for the snare drum, for example) at a minimum setting. n You can select any parameter here, but actual effect by the pad controller depends on the drum voice selected in the voice settings. 37