Yamaha IIs Owner's Manual - Page 94

Error Messages

Get Yamaha IIs PDF manuals and user guides
UPC - 086792645445
View all Yamaha IIs manuals
Add to My Manuals
Save this manual to your list of manuals

Page 94 highlights

Error Messages ERROR : MIDI input buffer full push [ENTER] MIDI buffer memory has become full by receiving too much MIDI data at a time via MIDI IN or TO HOST. Reduce the amount of data (data transfer rate) or increase the interval between each transfer on the sending device. ERROR : MIDI Illegal data push [ENTER] Received bulk data contains illegal data. Check if the data is not corrupted and appropriate for the DTXTREME IIs, and then retry. ERROR : MIDI data error push [ENTER] An error has occurred while MIDI data was being received. Check if the MIDI cable is properly connected and if the MIDI data is appropriate. WARNING: All data initialized push [ENTER] All setting data is initialized because the backup battery inside the DTXTREME IIs may be running short. Consult your nearest Yamaha dealer on replacing the battery. WARNING : Battery voltage is low push [ENTER] The backup battery inside the DTXTREME IIs may be running low. All setting data may be lost if the DTXTREME IIs is turned off after this message is shown. First try to save necessary data to a memory card or so on, then consult your nearest Yamaha dealer on replacing the battery. ERROR : MIDI check sum error push [ENTER] Checksum of the received bulk data is incorrect. Check if the data is not corrupted and appropriate for the DTXTREME IIs, and then retry. ERROR : Sequencer is Running push [ENTER] This message will be shown if you attempt an operation while the internal sequencer is running. Stop the sequencer and retry. ERROR : Sequence data is not empty push [ENTER] This message will be shown if you attempt recording to operation to the track that contains data. Retry recording to an empty track. ERROR : Memory full push [ENTER] User memory has become full. Save necessary user data to the memory card and clear unnecessary data to release the memory. ERROR : Card is write protected push [ENTER] This message will be shown if you attempt saving onto a write-protected memory card. Cancel write-protection of the memory card and retry. Appendix 94

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
Appendix
94
Error Messages
MIDI buffer memory has become full by receiving too much
MIDI data at a time via MIDI IN or TO HOST.
Reduce the
amount of data (data transfer rate) or increase the interval
between each transfer on the sending device.
An error has occurred while MIDI data was being received.
Check if the MIDI cable is properly connected and if the
MIDI data is appropriate.
All setting data is initialized because the backup battery inside
the DTXTREME IIs may be running short.
Consult your
nearest Yamaha dealer on replacing the battery.
The backup battery inside the DTXTREME IIs may be
running low.
All setting data may be lost if the DTXTREME
IIs is turned off after this message is shown.
First try to save
necessary data to a memory card or so on, then consult your
nearest Yamaha dealer on replacing the battery.
Checksum of the received bulk data is incorrect.
Check if the
data is not corrupted and appropriate for the DTXTREME
IIs, and then retry.
Received bulk data contains illegal data.
Check if the data is
not corrupted and appropriate for the DTXTREME IIs, and
then retry.
This message will be shown if you attempt an operation while
the internal sequencer is running.
Stop the sequencer and
retry.
This message will be shown if you attempt recording to
operation to the track that contains data.
Retry recording to
an empty track.
User memory has become full.
Save necessary user data to the
memory card and clear unnecessary data to release the
memory.
This message will be shown if you attempt saving onto a
write-protected memory card.
Cancel write-protection of the
memory card and retry.
ERROR : MIDI input buffer full
push [ENTER]
ERROR : MIDI data error
push [ENTER]
WARNING: All data initialized
push [ENTER]
WARNING : Battery voltage is low
push [ENTER]
ERROR : MIDI check sum error
push [ENTER]
ERROR : MIDI Illegal data
push [ENTER]
ERROR : Sequencer is Running
push [ENTER]
ERROR : Sequence data is not empty
push [ENTER]
ERROR : Memory full
push [ENTER]
ERROR : Card is write protected
push [ENTER]