Yamaha RX V2700 MCXSP10 Manual - Page 147

XM Satellite Radio U.S.A. and Canada models only, Remote control, Status message, Cause, Remedy - update

Get Yamaha RX V2700 - AV Network Receiver PDF manuals and user guides
UPC - 027108927077
View all Yamaha RX V2700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 147 highlights

TROUBLESHOOTING ■ XM Satellite Radio (U.S.A. and Canada models only) If an operation takes longer than usual or an error occurs, one of the following messages may appear in the front panel display. In this case, read the cause and follow the corresponding remedies. Status message Cause Remedy CHECK ANTENNA The XM Passport and XM Passport Home Check XM Passport and XM Passport Home Dock Dock are not connected to the XM jack of connections and orient for the best reception level. this unit or do not work properly. UPDATING The XM user encryption code is being updated. Wait until the encryption code is updated. NO SIGNAL The signal is too weak. Adjust the orientation of the XM Passport System for the best reception level. LOADING It takes longer than four seconds for audio Wait until the decoding process has finished. or text data to be decoded. OFF AIR The XM Satellite Radio channel you selected is not currently broadcasting any signals. Check the channel number again or select another XM Satellite Radio channel. - - - The Channel Station ID (SID) is no longer available. --- / --- No artist name or song title is available. - - - No channels are available for the selected category. Select another channel category by pressing CATEGORY on the front panel (or A-E/CAT. j / i on the remote control) repeatedly. ■ Remote control See page 63 - 63 - - 69 Problem The remote control does not work or function properly. Cause Remedy See page Wrong distance or angle. The remote control will function within a maximum range of 6 m (20 ft) and no more than 30 degrees off- 11 axis from the front panel. Direct sunlight or lighting (from an Reposition this unit. inverter type of fluorescent lamp, etc.) is striking the remote control sensor of this - unit. The batteries are weak. Replace all batteries. 11 The batteries do not last long and get quickly exhausted. Using alkaline batteries is strongly recommended. - The operation mode selector is set incorrectly. Set the operation mode selector correctly. When operating this unit, set it to the AMP position. When operating the component selected by the input selector button, set it to the SOURCE position. - When operating the TV set in the DTV or PHONO area, set it to the TV position. The remote control code was not correctly Set the remote control code correctly using set. "LIST OF REMOTE CONTROL CODES" at the end 120 of this manual. Try setting another code of the same manufacturer using "LIST OF REMOTE CONTROL CODES" at 120 the end of this manual. The library code of the remote control and Match the remote control ID of this unit with the the remote control ID of this unit do not corresponding remote control library code. match. 121, 135 ADDITIONAL INFORMATION 143 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
143
En
TROUBLESHOOTING
ADDITIONAL
INFORMATION
■
XM Satellite Radio (U.S.A. and Canada models only)
If an operation takes longer than usual or an error occurs, one of the following messages may appear in the front panel
display. In this case, read the cause and follow the corresponding remedies.
■
Remote control
Status message
Cause
Remedy
See
page
CHECK ANTENNA
The XM Passport and XM Passport Home
Dock are not connected to the XM jack of
this unit or do not work properly.
Check XM Passport and XM Passport Home Dock
connections and orient for the best reception level.
63
UPDATING
The XM user encryption code is being
updated.
Wait until the encryption code is updated.
—
NO SIGNAL
The signal is too weak.
Adjust the orientation of the XM Passport System for
the best reception level.
63
LOADING
It takes longer than four seconds for audio
or text data to be decoded.
Wait until the decoding process has finished.
—
OFF AIR
The XM Satellite Radio channel you
selected is not currently broadcasting any
signals.
Check the channel number again or select another
XM Satellite Radio channel.
—
<XM> - - -
The Channel Station ID (SID) is no longer
available.
- - -
/
- - -
No artist name or song title is available.
<CAT> - - -
No channels are available for the selected
category.
Select another channel category by pressing
CATEGORY on the front panel (or A-E/CAT.
j
/
i
on
the remote control) repeatedly.
69
Problem
Cause
Remedy
See
page
The remote control
does not work or
function properly.
Wrong distance or angle.
The remote control will function within a maximum
range of 6 m (20 ft) and no more than 30 degrees off-
axis from the front panel.
11
Direct sunlight or lighting (from an
inverter type of fluorescent lamp, etc.) is
striking the remote control sensor of this
unit.
Reposition this unit.
—
The batteries are weak.
Replace all batteries.
11
The batteries do not last long and get
quickly exhausted.
Using alkaline batteries is strongly recommended.
—
The operation mode selector is set
incorrectly.
Set the operation mode selector correctly.
When operating this unit, set it to the AMP position.
When operating the component selected by the input
selector button, set it to the SOURCE position.
When operating the TV set in the DTV or PHONO
area, set it to the TV position.
—
The remote control code was not correctly
set.
Set the remote control code correctly using
“LIST OF REMOTE CONTROL CODES” at the end
of this manual.
120
Try setting another code of the same manufacturer
using “LIST OF REMOTE CONTROL CODES” at
the end of this manual.
120
The library code of the remote control and
the remote control ID of this unit do not
match.
Match the remote control ID of this unit with the
corresponding remote control library code.
121, 135