Yamaha Tio1608-D2 Tio1608-D2 Owners Manual - Page 15
Manual setup, Head amp control, Settings con d by Quick Config, Tio1608-D2 procedure
View all Yamaha Tio1608-D2 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 15 highlights
Connection methods English 7. To assign the Tio1608-D2 inputs to the TF series mixing console, set the input select on the console's INPUT screen to "SLOT". NOTE While the INPUT screen is displayed, the menu keys can be used to change multiple currently selected FADER BANK inputs at the same time. 8. Adjust the input gain and other settings as necessary. Quick config is now complete. Settings configured by Quick Config Quick Config applies the following settings. • Dante settings Word clock Latency Encoding SECONDARY port mode Patching IP address 48 kHz (follower), no pull up/down 0.5 ms 24-bit PCM Daisy chain Refer to the table below Previous setting is used NOTE Quick Config does not configure analog input parameters. • Patching Tio input #1 ID 1, Input 1 ID 1, Input 2 : ID 1, Input 16 TF input Channel 1 Channel 2 : Channel 16 #2 ID 2, Input 1 ID 2, Input 2 : ID 2, Input 16 Channel 17 Channel 18 : Channel 32 #3 ID 3, Input 1 ID 3, Input 2 : ID 3, Input 8 Channel 33 Channel 34 : Channel 40 TF output Tio output AUX 1 ID 1, Output 1 : : AUX 6 Stereo L ID 1, Output 6 ID 1, Output 7 Stereo R AUX 7 ID 1, Output 8 ID 2, Output 1 : : AUX 12 ID 2, Output 6 Stereo L Stereo R AUX 13 ID 2, Output 7 ID 2, Output 8 ID 3, Output 1 : AUX 18 AUX 19 AUX 20 : ID 3, Output 6 ID 3, Output 7 ID 3, Output 8 NOTE • Even if only UNIT ID 2 or 3 is used, channels are patched as shown above based on the UNIT ID number. • After you have used Quick Config to configure the settings, you can use Dante Controller to change the individual settings. However, each time the Tio1608-D2 is turned on, Dante Controller settings will be replaced by the Quick Config settings. For this reason, we recommend that you turn Quick Config off if you are using Dante Controller. Manual setup If Quick Config is not used or if connecting to a mixer that does not support Quick Config, configure settings manually based on the given connection environment. Tio1608-D2 procedure 1. With the unit turned off, set the [QUICK CONFIG FOR TF] on the front panel to the [OFF] position. 2. Refer to the information on page 11 - 12 and set the DIP switches to the desired positions. 3. Set the [UNIT ID] on the front panel to the desired position. 4. Use Ethernet cables to connect the Tio1608-D2 to your Dante device. 5. Turn each device on. Dante settings When using manual setup, use Dante Controller to configure Dante settings. Dante Controller is a computer program that you can use to configure Dante network settings and audio signal patching settings. To use the program, download it from the Audinate website. (Dante Controller v3.2.1 or later is compatible with Tio1608-D2.) For information about Dante Controller, refer to the Dante Controller documentation. When using manual setup, you will need to use Dante Controller to configure the following settings at a minimum. (You can configure other settings as desired.) • Input and output patching settings (Network View Routing) • Clock leader settings (Network View Clock Status) • Sampling frequency settings (Device View Config) Head amp control You can use a Yamaha digital mixer or other device to control the Tio1608-D2 head amp. When the unit is connected to a TF series mixing console, you can control the unit's head amp just as you would adjust the console's head amp. When using a CL or QL series digital mixer, you can control or use the following parameters. • HA gain • +48 V phantom power on/off • HPF on/off • HPF frequency cutoff adjustment • Mute off • +48 V phantom power on/off display • Analog input level meter display • Firmware version display • Device identify • Dante SYSTEM and SYNC indicator information NOTE When the Dante SECONDARY port mode (page 12) is set to "Redundant connection", the head amp control function is only available via the Dante [PRIMARY]. The Dante [SECONDARY] is not available for this function. - 15 - Tio1608-D2 Owner's Manual