Yamaha Tio1608-D2 Tio1608-D2 Owners Manual - Page 16

Troubleshooting

Get Yamaha Tio1608-D2 PDF manuals and user guides View all Yamaha Tio1608-D2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Troubleshooting Troubleshooting Troubleshooting Issue No power, power indicator does not light Unit is not receiving an input signal Input level too low No sound heard [UNIT ID] or DIP switch settings not applied Cause Power cord not connected. Solution Make sure the power cord is connected (page 11). The power switch is turned off. Set the power switch to the "on" position. If you still cannot resolve the problem, please contact your nearest Yamaha representative. Cables not connected properly. Make sure all cables are connected properly. Source device is not sending a signal to the unit. Output a signal from the source device and confirm that the [STATUS INPUT] light. Internal head amp gain is too low. Adjust the internal head amp gain to an appropriate level. DIP switches are set to "refresh" mode but device that controls the Tio1608-D2 has not started up. Start the device that will control the Tio1608-D2 and send the settings to the Tio1608-D2. Set the [+48V ACTIVE] to the "on" position. Condenser mic is connected. Use the device that controls the Tio1608-D2 to turn on phantom power for the corresponding channel. Internal head amp gain is too low. Adjust the internal head amp gain to an appropriate level. Cables not connected properly. Make sure all cables are connected properly. DIP switches are set to "refresh" mode but device that controls the Tio1608-D2 has not started up. Start the device that will control the Tio1608-D2 and send the settings to the Tio1608-D2. The [QUICK CONFIG FOR TF] is ON in an environment where Quick Config cannot be used (when connected to mixer that does not support Quick Config or when settings were configured in Dante Controller). Set the [QUICK CONFIG FOR TF] to OFF and then try configuring the patch or other settings again. The sampling frequency does not Set the settings correctly in Dante Controller or match the connected mixer. other software. An error has occurred. Check the status of [SYSTEM] and [SYNC] and then resolve the problem accordingly. (page 17-18) You changed the switch positions Make sure the unit is turned off before while the unit was turned on. changing the switch positions. Tio1608-D2 Owner's Manual - 16 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
Troubleshooting
-
16
-
Owner’s Manual
Tio1608-D2
Troubleshooting
Troubleshooting
Issue
Cause
Solution
No power, power indicator does
not light
Power cord not connected.
Make sure the power cord is connected (
page
11
).
The power switch is turned off.
Set the power switch to the "on" position. If you
still cannot resolve the problem, please contact
your nearest Yamaha representative.
Unit is not receiving an input
signal
Cables not connected properly.
Make sure all cables are connected properly.
Source device is not sending a
signal to the unit.
Output a signal from the source device and
confirm that the [STATUS INPUT] light.
Internal head amp gain is too low.
Adjust the internal head amp gain to an
appropriate level.
DIP switches are set to "refresh"
mode but device that controls the
Tio1608-D2 has not started up.
Start the device that will control the Tio1608-D2
and send the settings to the Tio1608-D2.
Input level too low
Condenser mic is connected.
Set the [+48V ACTIVE] to the "on" position.
Use the device that controls the Tio1608-D2 to
turn on phantom power for the corresponding
channel.
Internal head amp gain is too low.
Adjust the internal head amp gain to an
appropriate level.
No sound heard
Cables not connected properly.
Make sure all cables are connected properly.
DIP switches are set to "refresh"
mode but device that controls the
Tio1608-D2 has not started up.
Start the device that will control the Tio1608-D2
and send the settings to the Tio1608-D2.
The [QUICK CONFIG FOR TF] is ON
in an environment where Quick
Config cannot be used (when
connected to mixer that does not
support Quick Config or when
settings were configured in Dante
Controller).
Set the [QUICK CONFIG FOR TF] to OFF and
then try configuring the patch or other settings
again.
The sampling frequency does not
match the connected mixer.
Set the settings correctly in Dante Controller or
other software.
An error has occurred.
Check the status of [SYSTEM] and [SYNC] and
then resolve the problem accordingly. (
page
17-18
)
[UNIT ID] or DIP switch settings
not applied
You changed the switch positions
while the unit was turned on.
Make sure the unit is turned off before
changing the switch positions.