1998 Ford Crown Victoria Owner's Manual - Page 41

1998 Ford Crown Victoria Manual

Get 1998 Ford Crown Victoria PDF manuals and user guides View all 1998 Ford Crown Victoria manuals

Page 41 highlights

Controls and features Note to Canadian residents During programming, your hand-held transmitter may automatically stop transmitting after two seconds which may not be long enough to program the HomeLink Universal Transmitter. If you are programming from one of these hand-held transmitters: • continue to hold the control on the HomeLink Universal Transmitter • re-press the hand-held transmitter every two seconds You may have to repeat this function several times while programming. Operating the HomeLink Universal Transmitter Once programmed, the HomeLink Universal Transmitter can be used in place of hand-held transmitters. To operate, simply press the appropriate channel control on the transmitter (the red light will illuminate, indicating the signal is being transmitted). Training a rolling code system Rolling code systems (garage door openers which are "code protected") may be determined by the following: • The hand-held transmitter appears to program the HomeLink Universal Transmitter but does not activate the garage door. • The garage door opener was manufactured after 1995. Follow these steps to train a garage door with the rolling code feature: 1. Locate the training control on the garage door opener receiver. Refer to the garage door opener manual or call 1-800-355-3515 if there is difficulty locating the training control. 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
Note to Canadian residents
During programming, your hand-held transmitter may automatically stop
transmitting after two seconds which may not be long enough to
program the HomeLink
t
Universal Transmitter.
If you are programming from one of
these hand-held transmitters:
•
continue to hold the control on
the HomeLink
t
Universal
Transmitter
•
re-press the hand-held
transmitter every two seconds
You may have to repeat this function
several times while programming.
Operating the HomeLink
T
Universal Transmitter
Once programmed, the HomeLink
t
Universal Transmitter can be used in
place of hand-held transmitters. To
operate, simply press the
appropriate channel control on the
transmitter (the red light will
illuminate, indicating the signal is
being transmitted).
Training a rolling code system
Rolling code systems (garage door openers which are “code protected”)
may be determined by the following:
•
The hand-held transmitter appears to program the HomeLink
t
Universal Transmitter but does not activate the garage door.
•
The garage door opener was manufactured after 1995.
Follow these steps to train a garage door with the rolling code feature:
1. Locate the training control on the garage door opener receiver. Refer
to the garage door opener manual or call 1–800–355–3515 if there is
difficulty locating the training control.
Controls and features
41