2008 Polaris Ranger 2x4 Owners Manual - Page 93

2008 Polaris Ranger 2x4 Manual

Get 2008 Polaris Ranger 2x4 PDF manuals and user guides View all 2008 Polaris Ranger 2x4 manuals

Page 93 highlights

MAINTENANCE Battery Battery Installation Using a new battery that has not been fully charged can damage the battery and result in a shorter life. It can also hinder vehicle performance. Follow the battery charging instructions on page 92 before installing the battery. 1. Ensure that the battery is fully charged. 2. Place the battery in the battery holder. Make sure the positive terminal is toward the driver's side of the vehicle. 3. With conventional batteries, install the battery vent tube (sealed batteries do not have a vent tube). NOTE: The vent tube must be free of obstructions and securely installed. Route the tube away from the frame and vehicle body to prevent contact with electrolyte. WARNING Battery gases could accumulate in an improperly installed vent tube and cause an explosion, resulting in serious injury or death. Always ensure that the vent tube is free of obstructions and is securely installed as recommended. 4. On conventional batteries, coat the terminals with dielectric grease or petroleum jelly. 5. Connect and tighten the red (positive) cable first. 6. Connect and tighten the black (negative) cable last. 7. Verify that cables are properly routed. 90

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
90
MAINTENANCE
Battery
Battery Installation
Using a new battery that has not been fully charged can damage the bat-
tery and result in a shorter life. It can also hinder vehicle performance.
Follow the battery charging instructions on page 92 before installing the
battery.
1.
Ensure that the battery is fully charged.
2.
Place the battery in the battery holder. Make sure the positive termi-
nal is toward the driver’s side of the vehicle.
3.
With conventional batteries, install the battery vent tube (sealed bat-
teries do not have a vent tube).
NOTE:
The vent tube must be free of obstructions and securely installed.
Route the tube away from the frame and vehicle body to prevent con-
tact with electrolyte.
4.
On conventional batteries, coat the terminals with dielectric grease
or petroleum jelly.
5.
Connect and tighten the red (positive) cable first.
6.
Connect and tighten the black (negative) cable last.
7.
Verify that cables are properly routed.
WARNING
Battery gases could accumulate in an improperly installed vent tube and
cause an explosion, resulting in serious injury or death. Always ensure that
the vent tube is free of obstructions and is securely installed as
recommended.